threadsizes

Bolt grade chart: SAE, ASTM and metric markings and strength

The size of a bolt says nothing about how strong it is; the grade does, and it is marked on the head. Inch bolts use SAE J429 grades (radial lines) or ASTM grades (stamped letters), metric bolts use ISO 898-1 property classes (stamped numbers), and stainless bolts ISO 3506-1 (steel type and class).

Reading the head: on SAE bolts, no lines = Grade 2, 3 radial lines = Grade 5, 6 radial lines = Grade 8 (lines plus two). Metric bolts carry the class number instead: 8.8, 10.9, 12.9.
Inch bolt grades: SAE J429, ASTM A307 and ASTM F3125 (minimums)
HeadGradeSize, inProof ksiYield ksiTensile ksiNut
Grade 2SAE J429Low or medium carbon steel 1/4 to 3/4 55379 MPa 57393 MPa 74510 MPa SAE J995 Grade 2or ASTM A563 Grade A
over 3/4 to 1-1/2 33228 MPa 36248 MPa 60414 MPa SAE J995 Grade 2or ASTM A563 Grade A
Grade 5SAE J429Medium carbon steel, quenched and tempered 1/4 to 1 85586 MPa 92634 MPa 120827 MPa SAE J995 Grade 5
over 1 to 1-1/2 74510 MPa 81558 MPa 105724 MPa SAE J995 Grade 5
Grade 8SAE J429Medium carbon alloy steel, quenched and tempered 1/4 to 1-1/2 120827 MPa 130896 MPa 1501034 MPa SAE J995 Grade 8
pending* Grade AASTM A307Low or medium carbon steel 1/4 to 4 none none 60414 MPa ASTM A563 Grade A
A325 Grade A325ASTM F3125Medium carbon steel, quenched and tempered 1/2 to 1-1/2 85586 MPa 92634 MPa 120827 MPa ASTM A563 DH heavy hex
A490 Grade A490ASTM F3125Alloy steel, quenched and tempered 1/2 to 1-1/2 120827 MPa 130896 MPa 1501034 MPa ASTM A563 DH heavy hex

Minimum values, ksi with MPa under each (1 ksi = 6.895 MPa). Proof load stress is the load a bolt must carry without taking a permanent stretch; yield is measured on a machined test piece; tensile is where it breaks. The proof load in pounds for a given size is this stress times the thread's tensile stress area. "None" means the standard sets no value. Nut: the matching SAE J995 or ASTM A563 nut; a stronger nut is always fine. Every value is a minimum for the full size range on its row; check the standard for the exact size and length you buy.

A325 and A490 have been grades of ASTM F3125 since 2016, when the stand-alone specifications were withdrawn. F3125 asks 120 ksi tensile and 92 ksi yield of every A325 size up to 1-1/2 in; many charts still print the old stand-alone A325 figures, 105 ksi tensile, 81 ksi yield and 74 ksi proof over 1 in. Structural bolts go with the matching heavy hex nut, and an ASTM F436 hardened washer where the joint uses one.

Metric property classes: ISO 898-1 (minimums)
HeadClassProof MPaYield MPaTensile MPaNut classReading the class
4.6 4.6Low or medium carbon steel 22533 ksi 24035 ksilower yield strength 40058 ksi pending* 4.6: 400 MPa nominal, yield 60% = 240 MPa nominal yield
4.8 4.8Low or medium carbon steel 31045 ksi 34049 ksistress at 0.0048d elongation 42061 ksi 5 4.8: 400 MPa nominal, yield 80% = 320 MPa nominal yield
5.8 5.8Low or medium carbon steel 38055 ksi 42061 ksistress at 0.0048d elongation 52075 ksi 5 5.8: 500 MPa nominal, yield 80% = 400 MPa nominal yield
8.8 8.8 up to M16Medium carbon steel, quenched and tempered 58084 ksi 64093 ksi0.2% proof stress 800116 ksi 8 8.8: 800 MPa nominal, yield 80% = 640 MPa nominal yield
8.8 over M16 60087 ksi 66096 ksi0.2% proof stress 830120 ksi
10.9 10.9Alloy or boron steel, quenched and tempered 830120 ksi 940136 ksi0.2% proof stress 1040151 ksi 10 10.9: 1000 MPa nominal, yield 90% = 900 MPa nominal yield
12.9 12.9Alloy steel, quenched and tempered 970141 ksi 1100160 ksi0.2% proof stress 1220177 ksi 12 12.9: 1200 MPa nominal, yield 90% = 1080 MPa nominal yield

Minimum values, MPa with ksi under each. ISO 898-1 covers M1.6 to M39; only class 8.8 changes with diameter, at 16 mm. Reading the class: the first number times 100 is the nominal tensile strength in MPa, the second times 10 the yield as a percentage of it. The nominal figures are round numbers; the minimums in the table are what a bolt must actually reach, and they can be a little higher. Yield is the lower yield strength on 4.6, the stress at 0.0048d plastic elongation (measured on the whole bolt) on 4.8 and 5.8, and the 0.2% proof stress from 8.8 up. Nut class: the ISO 898-2 nut for that bolt; a higher class nut is always fine.

Stainless bolts: ISO 3506-1 A2 and A4 (minimums)
HeadClassSteel0.2% proof stress MPaTensile MPaProof load stressNut
A2-70 A2-70 304-type (18-8) austenitic, cold worked 45065 ksi 700102 ksi none A2-70
A4-70 A4-70 316-type (with molybdenum) austenitic, cold worked 45065 ksi 700102 ksi none pending*
A4-80 A4-80 316-type (with molybdenum) austenitic, high strength 60087 ksi 800116 ksi none A4-80

A2 is the 304 family (18-8), A4 adds molybdenum and is the 316 family, the one for salt water and chemicals. The number after the dash is the class: 70 means 700 MPa minimum tensile, 80 means 800 MPa. ISO 3506-1 gives the 0.2% proof stress as the yield figure and sets no separate proof load stress for stainless bolts. Stainless is chosen for corrosion, not strength: even A4-80, at 600 MPa, yields below class 8.8 (640 MPa).

pending* Left blank until enough published sources agree. Have a chart that lists it? Send a source.

Grade 5 vs Grade 8 vs 8.8 vs 10.9

The four common high-strength grades, all in MPa (minimums)
GradeProofYieldTensile
Grade 5 (to 1 in)586634827
Class 8.8 (to M16)580640800
Grade 88278961034
Class 10.98309401040

Grade 5 is close to class 8.8: 827 against 800 MPa tensile, 634 against 640 MPa yield. Close, not equal: they come from different standards with different tests, and one has inch threads, the other metric.

Grade 8 is close to class 10.9: 1034 against 1040 MPa tensile, 896 against 940 MPa yield. Close, not equal: they come from different standards with different tests, and one has inch threads, the other metric.

Pick the grade the drawing or the maker calls for. Replacing a bolt with a stronger one is usually safe if the nut is upgraded with it; replacing it with a weaker one is not, and a stronger bolt can still fail first if the joint was designed around a softer one (a shear bolt, for example).

No torque values here

This page does not give tightening torques. The torque that reaches a given clamping force changes a lot with lubrication, plating or coating, the thread and the joint itself, so a single number per grade would be wrong for most real joints. Use the value in the service manual or on the drawing, or the bolt maker's data for that finish; structural bolts are installed by the method in their specification, not by a torque chart.

Questions

What do the lines on a bolt head mean?

On SAE inch bolts the radial lines give the grade: no lines = Grade 2, 3 radial lines = Grade 5, 6 radial lines = Grade 8. The grade is the number of lines plus two. A head with only the maker's mark is a Grade 2. Metric bolts do not use lines; they have the property class stamped on the head, such as 8.8 or 10.9.

Is 8.8 the same as Grade 5?

Close, but not the same. A Grade 5 bolt up to 1 in has a minimum tensile strength of 120 ksi (827 MPa) and a yield of 92 ksi (634 MPa); a class 8.8 bolt up to M16 has 800 MPa and 640 MPa. They are often used for the same jobs, but one has inch threads and the other metric, so they never swap on the same nut.

Which nut goes with a Grade 8 bolt?

A Grade 8 nut (SAE J995 Grade 8). The nut should be at least as strong as the bolt, so a Grade 8 nut also works on a Grade 5 or Grade 2 bolt, but a Grade 5 or Grade 2 nut on a Grade 8 bolt can strip before the bolt reaches its load. The metric equivalent is a class 10 nut on a 10.9 bolt.

What does 10.9 mean on a bolt?

It is the ISO property class. The first number times 100 is the nominal tensile strength in MPa (1000 MPa); the second number times 10 is the yield as a percentage of it (90%, so about 900 MPa). The minimums the standard actually requires are a little higher: 1040 MPa tensile and 940 MPa yield.

What is the difference between Grade 5 and Grade 8 bolts?

Grade 8 is stronger: 150 ksi minimum tensile against 120 ksi for Grade 5 up to 1 in, and a proof load stress of 120 ksi against 85 ksi. Grade 5 is medium carbon steel, quenched and tempered, Grade 8 medium carbon alloy steel, quenched and tempered. You can tell them apart by the head: Grade 5 has 3 radial lines, Grade 8 has 6.

Standards used: SAE J429 (inch bolt grades) and SAE J995 (inch nuts); ASTM A307, ASTM F3125 (A325 and A490) and ASTM A563 (nuts); ISO 898-1 and ISO 898-2 (metric bolts and nuts); ISO 3506-1 and ISO 3506-2 (stainless). For bolt and wrench sizes see the bolt size chart; full list on standards.