Washer size chart: SAE, USS and metric flat and lock washers
A washer is named by the bolt it goes on, not by its own hole: a 1/4 washer fits a 1/4 in bolt and an M6 washer an M6 bolt, and both have a hole a little bigger than the bolt. Inch flat washers come in two widths, SAE (narrow) and USS (wide), from ASME B18.22.1; metric ones follow ISO 7089 (normal) and ISO 7093-1 or DIN 9021 (large).
threadsizes.com/washer-size-chart · printed Nov 20, 2026 · check critical dimensions against the standard
| SAE (narrow) | USS (wide) | ||||||
|---|---|---|---|---|---|---|---|
| Size | ID | OD | Thick. min–max | ID | OD | Thick. min–max | Bolt |
| #2 | 0.094 | 0.250 | 0.020 0.016–0.025 | – | – | – | 2-56, 2-64 |
| #4 | 0.125 | 0.312 | 0.032 0.025–0.040 | – | – | – | 4-40, 4-48 |
| #6 | 0.156 | 0.375 | 0.049 0.036–0.065 | – | – | – | 6-32, 6-40 |
| #8 | 0.188 | 0.438 | 0.049 0.036–0.065 | – | – | – | 8-32, 8-36 |
| #10 | 0.219 | 0.500 | 0.049 0.036–0.065 | – | – | – | 10-24, 10-32 |
| #12 | 0.250 | 0.562 | 0.065 0.051–0.080 | – | – | – | 12-24, 12-28 |
| 1/4 | 0.281 | 0.625 | 0.065 0.051–0.080 | 0.312 | 0.734 | 0.065 0.051–0.080 | 1/4-20, 1/4-28 |
| 5/16 | 0.344 | 0.688 | 0.065 0.051–0.080 | 0.375 | 0.875 | 0.083 0.064–0.104 | 5/16-18, 5/16-24 |
| 3/8 | 0.406 | 0.812 | 0.065 0.051–0.080 | 0.438 | 1.000 | 0.083 0.064–0.104 | 3/8-16, 3/8-24 |
| 7/16 | 0.469 | 0.922 | 0.065 0.051–0.080 | 0.500 | 1.250 | 0.083 0.064–0.104 | 7/16-14, 7/16-20 |
| 1/2 | 0.531 | 1.062 | 0.095 0.074–0.121 | 0.562 | 1.375 | 0.109 0.086–0.132 | 1/2-13, 1/2-20 |
| 9/16 | 0.594 | 1.156 | 0.095 0.074–0.121 | 0.625 | 1.469 | 0.109 0.086–0.132 | 9/16-12, 9/16-18 |
| 5/8 | 0.656 | 1.312 | 0.095 0.074–0.121 | 0.688 | 1.750 | 0.134 0.108–0.160 | 5/8-11, 5/8-18 |
| 3/4 | 0.812 | 1.469 | 0.134 0.108–0.160 | 0.812 | 2.000 | 0.148 0.122–0.177 | 3/4-10, 3/4-16 |
| 7/8 | 0.938 | 1.750 | 0.134 0.108–0.160 | 0.938 | 2.250 | 0.165 0.136–0.192 | 7/8-9, 7/8-14 |
| 1 | 1.062 | 2.000 | 0.134 0.108–0.160 | 1.062 | 2.500 | 0.165 0.136–0.192 | 1-8, 1-12 |
| 1-1/8 | 1.250 | 2.250 | 0.134 0.108–0.160 | 1.250 | 2.750 | 0.165 0.136–0.192 | 1-1/8-7, 1-1/8-12 |
| 1-1/4 | 1.375 | 2.500 | 0.165 0.136–0.192 | 1.375 | 3.000 | 0.165 0.136–0.192 | 1-1/4-7, 1-1/4-12 |
| 1-3/8 | 1.500 | 2.750 | 0.165 0.136–0.192 | 1.500 | 3.250 | 0.180 0.153–0.213 | 1-3/8-6, 1-3/8-12 |
| 1-1/2 | 1.625 | 3.000 | 0.165 0.136–0.192 | 1.625 | 3.500 | 0.180 0.153–0.213 | 1-1/2-6, 1-1/2-12 |
| 1-5/8 | – | – | – | 1.750 | 3.750 | 0.180 0.153–0.213 | – |
| 1-3/4 | – | – | – | 1.875 | 4.000 | 0.180 0.153–0.213 | 1-3/4-5 |
| 1-7/8 | – | – | – | 2.000 | 4.250 | 0.180 0.153–0.213 | – |
| 2 | – | – | – | 2.125 | 4.500 | 0.180 0.153–0.213 | 2-4.5 |
| 2-1/4 | – | – | – | 2.375 | 4.750 | 0.220 0.193–0.248 | – |
| 2-1/2 | – | – | – | 2.625 | 5.000 | 0.238 0.210–0.280 | – |
| 2-3/4 | – | – | – | 2.875 | 5.250 | 0.259 0.228–0.310 | – |
| 3 | – | – | – | 3.125 | 5.500 | 0.284 0.249–0.327 | – |
ID is the hole, OD the outside diameter, both basic sizes; thickness is nominal with the allowed range. Catalogs sell the B18.22.1 narrow (N) series as SAE and the wide (W) series as USS. Below 1/4 the standard has one size only, sold as SAE, so there is no USS washer there; above 1-1/2 it has one size only again, sold as USS. Bolt is the UNC and UNF thread of the same diameter; either thread takes the same washer. For mm, multiply by 25.4.
| Size | d1 hole min, max | d2 OD max, min | h thick. min–max | Thread |
|---|---|---|---|---|
| M2 | 2.2 max 2.34 | 5 min 4.7 | 0.3 0.25–0.35 | M2 x 0.4 |
| M2.5 | 2.7 max 2.84 | 6 min 5.7 | 0.5 0.45–0.55 | M2.5 x 0.45 |
| M3 | 3.2 max 3.38 | 7 min 6.64 | 0.5 0.45–0.55 | M3 x 0.5 |
| M3.5 | 3.7 max 3.88 | 8 min 7.64 | 0.5 0.45–0.55 | M3.5 x 0.6 |
| M4 | 4.3 max 4.48 | 9 min 8.64 | 0.8 0.7–0.9 | M4 x 0.7 |
| M5 | 5.3 max 5.48 | 10 min 9.64 | 1 0.9–1.1 | M5 x 0.8 |
| M6 | 6.4 max 6.62 | 12 min 11.57 | 1.6 1.4–1.8 | M6 x 1 |
| M8 | 8.4 max 8.62 | 16 min 15.57 | 1.6 1.4–1.8 | M8 x 1.25 |
| M10 | 10.5 max 10.77 | 20 min 19.48 | 2 1.8–2.2 | M10 x 1.5 |
| M12 | 13 max 13.27 | 24 min 23.48 | 2.5 2.3–2.7 | M12 x 1.75 |
| M14 | 15 max 15.27 | 28 min 27.48 | 2.5 2.3–2.7 | M14 x 2 |
| M16 | 17 max 17.27 | 30 min 29.48 | 3 2.7–3.3 | M16 x 2 |
| M18 | 19 max 19.33 | 34 min 33.38 | 3 2.7–3.3 | M18 x 2.5 |
| M20 | 21 max 21.33 | 37 min 36.38 | 3 2.7–3.3 | M20 x 2.5 |
| M22 | 23 max 23.33 | 39 min 38.38 | 3 2.7–3.3 | M22 x 2.5 |
| M24 | 25 max 25.33 | 44 min 43.38 | 4 3.7–4.3 | M24 x 3 |
| M27 | 28 max 28.33 | 50 min 49.38 | 4 3.7–4.3 | – |
| M30 | 31 max 31.39 | 56 min 55.26 | 4 3.7–4.3 | – |
| M33 | 34 max 34.62 | 60 min 58.8 | 5 4.4–5.6 | – |
| M36 | 37 max 37.62 | 66 min 64.8 | 5 4.4–5.6 | – |
| M39 | 42 max 42.62 | 72 min 70.8 | 6 5.4–6.6 | – |
| M42 | 45 max 45.62 | 78 min 76.8 | 8 7–9 | – |
| M45 | 48 max 48.62 | 85 min 83.6 | 8 7–9 | – |
| M48 | 52 max 52.74 | 92 min 90.6 | 8 7–9 | – |
| M52 | 56 max 56.74 | 98 min 96.6 | 8 7–9 | – |
| M56 | 62 max 62.74 | 105 min 103.6 | 10 9–11 | – |
| M60 | 66 max 66.74 | 110 min 108.6 | 10 9–11 | – |
| M64 | 70 max 70.74 | 115 min 113.6 | 10 9–11 | – |
d1 is the hole, with the largest the standard allows under it; d2 is the outside diameter, with the smallest allowed; h is the nominal thickness with its range. A washer that measures inside those limits is in spec. This is the default washer under a metric hex bolt or nut; the same sizes with a chamfer on one side are ISO 7090 (DIN 125-B).
| ISO 7093-1 | DIN 9021 | |||||
|---|---|---|---|---|---|---|
| Size | d1 hole | d2 OD | h thick. | d1 hole | d2 OD | h thick. |
| M2.5 | – | – | – | 2.7 | 8 | 0.8 |
| M3 | 3.2 | 9 | 0.8 | 3.2 | 9 | 0.8 |
| M3.5 | 3.7 | 11 | 0.8 | 3.7 | 11 | 0.8 |
| M4 | 4.3 | 12 | 1 | 4.3 | 12 | 1 |
| M5 | 5.3 | 15 | 1.2 | 5.3 | 15 | 1.2 |
| M6 | 6.4 | 18 | 1.6 | 6.4 | 18 | 1.6 |
| M7 | – | – | – | 7.4 | 22 | 2 |
| M8 | 8.4 | 24 | 2 | 8.4 | 24 | 2 |
| M10 | 10.5 | 30 | 2.5 | 10.5 | 30 | 2.5 |
| M12 | 13 | 37 | 3 | 13 | 37 | 3 |
| M14 | 15 | 44 | 3 | 15 | 44 | 3 |
| M16 | 17 | 50 | 3 | 17 | 50 | 3 |
| M18 | 19 | 56 | 4 | 20 | 56 | 4 |
| M20 | 21 | 60 | 4 | 22 | 60 | 4 |
| M22 | 23 | 66 | 5 | – | – | – |
| M24 | 25 | 72 | 5 | 26 | 72 | 5 |
| M27 | 30 | 85 | 6 | – | – | – |
| M30 | 33 | 92 | 6 | 33 | 92 | 6 |
| M33 | 36 | 105 | 6 | – | – | – |
| M36 | 39 | 110 | 8 | 39 | 110 | 8 |
Large washers are about three times the bolt diameter across, for slotted holes, thin sheet and soft materials. DIN 9021 is what most shops sell as the metric fender or "penny" washer; it was withdrawn in Germany but is still made, and it has no M2, M22 or M27. Where both list a size, outside diameter and thickness are the same; the hole differs on M18, M20, M24, where DIN 9021's is larger.
Split lock washers
| Size | ID min–max | OD max | Thickness min | Section width min |
|---|---|---|---|---|
| #2 | 0.088–0.094 | 0.172 | 0.020 | 0.035 |
| #3 | 0.101–0.107 | 0.195 | 0.025 | 0.040 |
| #4 | 0.114–0.120 | 0.209 | 0.025 | 0.040 |
| #5 | 0.127–0.133 | 0.236 | 0.031 | 0.047 |
| #6 | 0.141–0.148 | 0.250 | 0.031 | 0.047 |
| #8 | 0.167–0.174 | 0.293 | 0.040 | 0.055 |
| #10 | 0.193–0.200 | 0.334 | 0.047 | 0.062 |
| #12 | 0.220–0.227 | 0.377 | 0.056 | 0.070 |
| 1/4 | 0.252–0.260 | 0.487 | 0.062 | 0.109 |
| 5/16 | 0.314–0.322 | 0.583 | 0.078 | 0.125 |
| 3/8 | 0.377–0.385 | 0.680 | 0.094 | 0.141 |
| 7/16 | 0.440–0.450 | 0.776 | 0.109 | 0.156 |
| 1/2 | 0.502–0.512 | 0.869 | 0.125 | 0.171 |
| 9/16 | 0.564–0.574 | 0.965 | 0.141 | 0.188 |
| 5/8 | 0.628–0.641 | 1.073 | 0.156 | 0.203 |
| 11/16 | 0.691–0.704 | 1.170 | 0.172 | 0.219 |
| 3/4 | 0.753–0.766 | 1.265 | 0.188 | 0.234 |
| 13/16 | 0.816–0.832 | 1.363 | 0.203 | 0.250 |
| 7/8 | 0.878–0.894 | 1.459 | 0.219 | 0.266 |
| 15/16 | 0.941–0.958 | 1.556 | 0.234 | 0.281 |
| 1 | 1.003–1.024 | 1.656 | 0.250 | 0.297 |
| 1-1/8 | 1.129–1.153 | 1.847 | 0.281 | 0.328 |
| 1-1/4 | 1.254–1.280 | 2.036 | 0.312 | 0.359 |
| 1-3/8 | 1.379–1.408 | 2.219 | 0.344 | 0.391 |
| 1-1/2 | 1.504–1.534 | 2.419 | 0.375 | 0.422 |
| 1-3/4 | 1.758–1.789 | 2.679 | 0.389 | 0.424 |
| 2 | 2.008–2.039 | 2.936 | 0.422 | 0.427 |
| Size | d1 hole min, max | d2 OD max | s thickness | b width | Free height min–max |
|---|---|---|---|---|---|
| M2 | 2.1 max 2.4 | 4.4 | 0.5 | 0.9 | 1–1.2 |
| M2.2 | 2.3 max 2.6 | 4.8 | 0.6 | 1 | 1.2–1.4 |
| M2.5 | 2.6 max 2.9 | 5.1 | 0.6 | 1 | 1.2–1.4 |
| M3 | 3.1 max 3.4 | 6.2 | 0.8 | 1.3 | 1.6–1.9 |
| M3.5 | 3.6 max 3.9 | 6.7 | 0.8 | 1.3 | 1.6–1.9 |
| M4 | 4.1 max 4.4 | 7.6 | 0.9 | 1.5 | 1.8–2.1 |
| M5 | 5.1 max 5.4 | 9.2 | 1.2 | 1.8 | 2.4–2.8 |
| M6 | 6.1 max 6.5 | 11.8 | 1.6 | 2.5 | 3.2–3.8 |
| M7 | 7.1 max 7.5 | 12.8 | 1.6 | 2.5 | 3.2–3.8 |
| M8 | 8.1 max 8.5 | 14.8 | 2 | 3 | 4–4.7 |
| M10 | 10.2 max 10.7 | 18.1 | 2.2 | 3.5 | 4.4–5.2 |
| M12 | 12.2 max 12.7 | 21.1 | 2.5 | 4 | 5–5.9 |
| M14 | 14.2 max 14.7 | 24.1 | 3 | 4.5 | 6–7.1 |
| M16 | 16.2 max 17 | 27.4 | 3.5 | 5 | 7–8.3 |
| M18 | 18.2 max 19 | 29.4 | 3.5 | 5 | 7–8.3 |
| M20 | 20.2 max 21.2 | 33.6 | 4 | 6 | 8–9.4 |
| M22 | 22.5 max 23.5 | 35.9 | 4 | 6 | 8–9.4 |
| M24 | 24.5 max 25.5 | 40 | 5 | 7 | 10–11.8 |
| M27 | 27.5 max 28.5 | 43 | 5 | 7 | 10–11.8 |
| M30 | 30.5 max 31.7 | 48.2 | 6 | 8 | 12–14.2 |
| M36 | 36.5 max 37.7 | 58.2 | 6 | 10 | 12–14.2 |
| M39 | 39.5 max 40.7 | 61.2 | 6 | 10 | 12–14.2 |
| M42 | 42.5 max 43.7 | 68.2 | 7 | 12 | 14–16.5 |
| M45 | 45.5 max pending* | 71.2 | 7 | 12 | 14–16.5 |
| M48 | 49 max pending* | 75 | 7 | 12 | 14–16.5 |
Thickness on an inch lock washer is the mean of its two ends, the minimum the standard allows; section width is the radial width of the coil. On DIN 127 B, b is the width of the coil and the free height is the uncompressed height of the split washer. DIN 127 was withdrawn in Germany but lock washers are still sold to it; form B has flat ends, form A tanged ends.
Fender washers
No governing standard: maker values. An inch fender washer is named by bolt size and outside diameter (1/4 x 1-1/4 fits a 1/4 in bolt and is 1-1/4 in across), but the hole and the thickness change from maker to maker: for 1/4 x 1-1/4 the published holes are 0.281 in (AFT Fasteners) and 0.250 in (Lawson Products). Check the part you buy. For metric, the large-series DIN 9021 washer is the fender washer.
| Size | Maker | ID | OD | Thickness min–max |
|---|---|---|---|---|
| #10 x 11/16 | AFT Fasteners * | 0.219 | 0.688 | 0.036–0.080 |
| #10 x 3/4 | AFT Fasteners * | 0.219 | 0.750 | 0.036–0.080 |
| #10 x 7/8 | AFT Fasteners * | 0.219 | 0.875 | 0.036–0.080 |
| #10 x 1 | AFT Fasteners * | 0.219 | 1.000 | 0.036–0.084 |
| #10 x 1-1/4 | AFT Fasteners * | 0.219 | 1.250 | 0.036–0.084 |
| #10 x 1-1/2 | AFT Fasteners * | 0.219 | 1.500 | 0.036–0.080 |
| #10 x 2 | AFT Fasteners * | 0.219 | 2.000 | 0.036–0.080 |
| 1/4 x 1 | AFT Fasteners * | 0.281 | 1.000 | 0.036–0.132 |
| 1/4 x 1-1/4 | AFT Fasteners * | 0.281 | 1.250 | 0.036–0.132 |
| 1/4 x 1-1/4 | Lawson Products 540 * | 0.250 | 1.250 | 0.060 |
| 1/4 x 1-1/4 | Fastener Superstore 405047 * | not listed | 1.250 | 0.047–0.080 |
| 1/4 x 1-1/2 | AFT Fasteners * | 0.281 | 1.500 | 0.036–0.132 |
| 1/4 x 1-3/4 | AFT Fasteners * | 0.281 | 1.750 | 0.036–0.080 |
| 1/4 x 2 | AFT Fasteners * | 0.281 | 2.000 | 0.036–0.080 |
| 5/16 x 1 | AFT Fasteners * | 0.344 | 1.000 | 0.036–0.080 |
| 5/16 x 1-1/4 | AFT Fasteners * | 0.344 | 1.250 | 0.036–0.132 |
| 5/16 x 1-1/2 | AFT Fasteners * | 0.344 | 1.500 | 0.036–0.132 |
| 5/16 x 2 | AFT Fasteners * | 0.344 | 2.000 | 0.036–0.080 |
| 5/16 x 2-1/2 | AFT Fasteners * | 0.344 | 2.500 | 0.036–0.080 |
| 3/8 x 1-1/4 | AFT Fasteners * | 0.406 | 1.250 | 0.036–0.132 |
| 3/8 x 1-1/2 | AFT Fasteners * | 0.406 | 1.500 | 0.036–0.132 |
| 3/8 x 2 | AFT Fasteners * | 0.422 | 2.000 | 0.051–0.080 |
| 3/8 x 2-1/2 | AFT Fasteners * | 0.422 | 2.500 | 0.051–0.080 |
| 1/2 x 1-1/4 | AFT Fasteners * | 0.531 | 1.250 | 0.051–0.080 |
| 1/2 x 1-1/2 | AFT Fasteners * | 0.531 | 1.500 | 0.051–0.080 |
| 1/2 x 1-3/4 | AFT Fasteners * | 0.531 | 1.750 | 0.051–0.080 |
| 1/2 x 2 | AFT Fasteners * | 0.531 | 2.000 | 0.051–0.132 |
| 1/2 x 2-1/2 | AFT Fasteners * | 0.531 | 2.500 | 0.051–0.080 |
| 1/2 x 3 | AFT Fasteners * | 0.531 | 3.000 | 0.051–0.080 |
| 5/8 x 1-1/4 | AFT Fasteners * | 0.688 | 1.250 | 0.074–0.084 |
| 5/8 x 2 | AFT Fasteners * | 0.688 | 2.000 | 0.051–0.080 |
| 5/8 x 3 | AFT Fasteners * | 0.688 | 3.000 | 0.051–0.080 |
| 3/4 x 2 | AFT Fasteners * | 0.812 | 2.000 | 0.051–0.080 |
| 7/8 x 2-1/2 | AFT Fasteners * | 0.938 | 2.500 | 0.101–0.118 |
* Maker-only: each row is the maker's or catalog's own listing, with no independent measurement behind it. A single thickness is the maker's nominal; a range is its min–max.
pending* Left blank until enough published sources agree. Have a chart that lists it? Send a source.
Hardened washers and bolt grades
Under a high-strength bolt, a soft washer can dent under the head and let the joint lose clamping force. ISO 7089 washers come in two hardness classes: 200 HV is for hex bolts and screws up to property class 8.8 and nuts up to class 8, 300 HV for bolts up to 10.9 and nuts up to class 10. Both look the same, so check the box or the order code before putting a washer under a 10.9 bolt.
Inch SAE and USS washers are sold two ways. Plain ones have no hardness requirement at all and no marking. Hardened ones are made to ASTM F436 and must be marked; they are the ones to use with structural bolts and other high-strength bolting.
USS vs SAE washers: what's the difference?
For the same bolt, a USS washer is wider and has a slightly larger hole; an SAE washer is narrower and fits the bolt more closely. On a 1/2 in bolt the SAE washer is 1.062 in across with a 0.531 in hole, the USS washer 1.375 in across with a 0.562 in hole, and thicker: 0.109 in against 0.095 in.
The names come from two old thread standards: the United States Standard coarse thread and the SAE fine thread. Today the washer fits the bolt's diameter, not its pitch, so either washer goes on a UNC or a UNF bolt. Pick USS to spread the load on wood, plastic or a slotted hole, and SAE where a wide washer will not fit, such as next to a hex nut on machinery or under a socket head cap screw in a counterbore.
Which washer for which bolt
| Series | Standard | OD vs bolt | Thickness | Use it for |
|---|---|---|---|---|
| Flat, normal | ISO 7089 (DIN 125-A) | 1.8–2.5× | 0.3–10 mm | The default under a metric hex bolt or nut. 300 HV for 10.9 bolts. |
| Flat, large | ISO 7093-1, DIN 9021 | 3.0–3.2× | 0.8–8 mm | Slotted or oversized holes, thin sheet, soft materials. |
| SAE flat | ASME B18.22.1 narrow | 2.0–2.9× | 0.020–0.165 in | Machinery and automotive work, close-fit holes, tight spots next to a nut. |
| USS flat | ASME B18.22.1 wide | 1.8–2.9× | 0.065–0.284 in | Wood, construction, ragged or oversized holes. |
| Fender | none (maker values) | 2.0–10.5× | 0.036–0.132 in | Sheet metal and panels: the biggest bearing face on a small screw. |
| Split lock | ASME B18.21.1 regular | 1.5–2.0× | 0.020–0.422 in | Older drawings that call for one. Against vibration, thread locker or a prevailing-torque nut usually holds better. |
| Split lock | DIN 127 B | 1.6–2.2× | 0.5–7 mm | Same as the inch split lock washer. |
OD vs bolt is the outside diameter divided by the bolt diameter, smallest to largest size in each table above; small screw sizes sit at the top of the range.
Match the washer's size to the bolt: a 3/8 washer for any 3/8 in bolt, coarse or fine, an M10 washer for an M10 bolt. The washer's hole is about the size of the bolt's clearance hole; what matters is the outside diameter, which should cover the bolt head or nut and spreads the load around the hole. On the inch and metric bolt charts the wrench size is the head's width across the flats. For a slotted hole or soft material, go up to USS, a large metric washer or a fender washer.
Download as CSV
Every value on this page in one CSV file for a spreadsheet: one row per washer, with the standard, unit and tolerances. Pending values are left empty; fender rows are marked maker-only. Each table also has its own PNG, linked next to the table's title.
Questions
What size washer for an M6 bolt?
A plain M6 washer (ISO 7089, normal series) is 6.4 mm inside, 12 mm outside, 1.6 mm thick. The large series (ISO 7093-1), for slotted or soft parts, is 6.4 × 18 × 1.6 mm. An M6 split lock washer (DIN 127 B) is 11.8 mm across and 1.6 mm thick.
What are the dimensions of an M8 washer?
An M8 flat washer (ISO 7089) is 8.4 mm inside, 16 mm outside and 1.6 mm thick. The large M8 washer (ISO 7093-1) is 8.4 × 24 × 2 mm. An M8 split lock washer (DIN 127 B) is 8.1 mm inside (min), 14.8 mm outside (max) and 2 mm thick.
What is the difference between USS and SAE washers?
For the same bolt, a USS washer is wider, has a slightly bigger hole and is often thicker. A 1/2 in SAE washer is 0.531 x 1.062 x 0.095 in (inside x outside x thickness); a 1/2 in USS washer is 0.562 x 1.375 x 0.109 in. Use SAE where the washer has to fit next to a nut or in a tight spot, USS to spread the load on wood or soft material.
Is a 1/4 washer 1/4 inch inside?
No. The size is the bolt it fits, and the hole is a little bigger so the bolt goes through: 0.281 in (9/32) on a 1/4 SAE washer and 0.312 in (5/16) on a 1/4 USS washer. The outside diameters are 0.625 in and 0.734 in.
Is DIN 125 the same as ISO 7089?
ISO 7089 replaced DIN 125-A, the plain flat washer without a chamfer; the chamfered DIN 125-B became ISO 7090. Washers are still sold under both names. ISO 7089 lists the washer by the thread it goes on (M6) and gives the hole d1, the outside diameter d2 and the thickness h.
Standards used: ASME B18.22.1 (plain washers) and ASME B18.21.1 (lock washers) for inch; ISO 7089, ISO 7093-1, DIN 9021 and DIN 127 for metric; ASTM F436 for hardened inch washers. Fender washers: AFT Fasteners, Lawson Products, Fastener Superstore catalog listings. Full list on standards.