Clearance hole chart (inch and metric)
A clearance hole is the hole a screw passes through without engaging a thread, so it is larger than the screw. A tap drill is the opposite: the smaller hole you cut a thread into. Three fits are listed for each size: close, normal and loose. Normal fit is the default.
threadsizes.com/clearance-hole-chart · printed Nov 20, 2026 · check critical dimensions against the standard
Inch (UNC/UNF), ASME B18.2.8
| Clearance hole | Tap drill (to cut a thread) | ||||
|---|---|---|---|---|---|
| Screw | Close | Normal | Loose | UNC | UNF |
| #0 | #51 0.0670 | #48 0.0760 | 3/32" 0.0938 | – | 3/64" 0.0469 |
| #1 | #46 0.0810 | #43 0.0890 | #37 0.1040 | #53 0.0595 | #53 0.0595 |
| #2 | 3/32" 0.0938 | #38 0.1015 | #32 0.1160 | #50 0.0700 | #50 0.0700 |
| #3 | #36 0.1065 | #32 0.1160 | #30 0.1285 | #47 0.0785 | #45 0.0820 |
| #4 | #31 0.1200 | #30 0.1285 | #27 0.1440 | #43 0.0890 | #42 0.0935 |
| #5 | 9/64" 0.1406 | 5/32" 0.1563 | 11/64" 0.1719 | #38 0.1015 | #37 0.1040 |
| #6 | #23 0.1540 | #18 0.1695 | #13 0.1850 | #36 0.1065 | #33 0.1130 |
| #8 | #15 0.1800 | #9 0.1960 | #3 0.2130 | #29 0.1360 | #29 0.1360 |
| #10 | #5 0.2055 | #2 0.2210 | B 0.2380 | #25 0.1495 | #21 0.1590 |
| #12 | † | † | † | #16 0.1770 | #14 0.1820 |
| 1/4 | 17/64" 0.2656 | 9/32" 0.2813 | 19/64" 0.2969 | #7 0.2010 | #3 0.2130 |
| 5/16 | 21/64" 0.3281 | 11/32" 0.3438 | 23/64" 0.3594 | F 0.2570 | I 0.2720 |
| 3/8 | 25/64" 0.3906 | 13/32" 0.4063 | 27/64" 0.4219 | 5/16" 0.3125 | Q 0.3320 |
| 7/16 | 29/64" 0.4531 | 15/32" 0.4688 | 31/64" 0.4844 | U 0.3680 | 25/64" 0.3906 |
| 1/2 | 17/32" 0.5313 | 9/16" 0.5625 | 39/64" 0.6094 | 27/64" 0.4219 | 29/64" 0.4531 |
| 9/16 | † | † | † | 31/64" 0.4844 | 33/64" 0.5156 |
| 5/8 | 21/32" 0.6563 | 11/16" 0.6875 | 47/64" 0.7344 | 17/32" 0.5313 | 37/64" 0.5781 |
| 11/16 | † | † | † | – | – |
| 3/4 | 25/32" 0.7813 | 13/16" 0.8125 | 29/32" 0.9063 | 21/32" 0.6563 | 11/16" 0.6875 |
| 13/16 | † | † | † | – | – |
| 7/8 | 29/32" 0.9063 | 15/16" 0.9375 | 1-1/32" 1.0313 | 49/64" 0.7656 | 13/16" 0.8125 |
| 15/16 | † | † | † | – | – |
| 1 | 1-1/32" 1.0313 | 1-3/32" 1.0938 | 1-5/32" 1.1563 | 7/8" 0.8750 | 59/64" 0.9219 |
Metric, ISO 273
| Clearance hole | Tap drill (to cut a thread) | ||||
|---|---|---|---|---|---|
| Size | Close | Medium (normal) | Coarse (loose) | Coarse thread | Fine thread |
| M1.6 | 1.7 mm | 1.8 mm | 2 mm | M1.6 x 0.35: 1.25 mm | – |
| M2 | 2.2 mm | 2.4 mm | 2.6 mm | M2 x 0.4: 1.6 mm | – |
| M2.5 | 2.7 mm | 2.9 mm | 3.1 mm | M2.5 x 0.45: 2.05 mm | – |
| M3 | 3.2 mm | 3.4 mm | 3.6 mm | M3 x 0.5: 2.5 mm | – |
| M3.5 | 3.7 mm | 3.9 mm | 4.2 mm | M3.5 x 0.6: 2.9 mm | – |
| M4 | 4.3 mm | 4.5 mm | 4.8 mm | M4 x 0.7: 3.3 mm | – |
| M5 | 5.3 mm | 5.5 mm | 5.8 mm | M5 x 0.8: 4.2 mm | – |
| M6 | 6.4 mm | 6.6 mm | 7 mm | M6 x 1: 5 mm | M6 x 0.75: 5.2 mm |
| M8 | 8.4 mm | 9 mm | 10 mm | M8 x 1.25: 6.8 mm | M8 x 1: 7 mm |
| M10 | 10.5 mm | 11 mm | 12 mm | M10 x 1.5: 8.5 mm | M10 x 1.25: 8.8 mm M10 x 1: 9 mm |
| M12 | 13 mm | 13.5 mm | 14.5 mm | M12 x 1.75: 10.2 mm | M12 x 1.5: 10.5 mm M12 x 1.25 not verified* |
| M14 | 15 mm | 15.5 mm | 16.5 mm | M14 x 2: 12 mm | M14 x 1.5: 12.5 mm |
| M16 | 17 mm | 17.5 mm | 18.5 mm | M16 x 2: 14 mm | M16 x 1.5: 14.5 mm |
| M18 | 19 mm | 20 mm | 21 mm | M18 x 2.5: 15.5 mm | M18 x 1.5 not verified* |
| M20 | 21 mm | 22 mm | 24 mm | M20 x 2.5: 17.5 mm | M20 x 1.5: 18.5 mm |
| M22 | 23 mm | 24 mm | 26 mm | M22 x 2.5: 19.5 mm | M22 x 1.5: 20.5 mm |
| M24 | 25 mm | 26 mm | 28 mm | M24 x 3: 21 mm | M24 x 2: 22 mm |
† Not in ASME B18.2.8-1999 Table 1 (preferred sizes only). The older ASME two-fit (Close / Free) drills for these sizes are shown on the thread page itself; see #12 and 9/16 for examples.
Inch holes are the ASME B18.2.8 fits, drill and decimal inch. ISO 273 calls the three metric fits close, medium and coarse (fit names, nothing to do with coarse and fine thread pitch); they are the close, normal and loose columns. Inch decimals are shown to four places, so 13/16 reads 0.8125. Tap drills on the tap drill and metric tap drill charts. Standards used: ASME B18.2.8 and ISO 273. Data last checked 3 November 2026.
Which fit to use
- NormalThe default for a screw that passes through the part. Use it unless you have a reason not to.
- CloseLocates the part more accurately but allows less error in hole position.
- LooseGives the most room when holes may not line up, for example in rough or welded work.
A washer under the head or nut covers the clearance hole: see the washer size chart for the washer that goes with each size.
Looking for the hole to tap instead? See the tap drill chart and the metric tap drill chart.