Thread pitch chart
Pitch is the distance from one thread crest to the next. Inch threads give it as threads per inch (TPI): 1/4-20 has 20, so the pitch is 1/20 in, or 25.4 ÷ 20 = 1.27 mm. Metric threads give the pitch itself in millimeters: M8 x 1.25. A plain "M8" or "1/4 UNC" always means the coarse pitch.
threadsizes.com/thread-pitch-chart · printed Nov 20, 2026 · check critical dimensions against the standard
| Size | Major dia. | mm | UNC TPI | Pitch | UNF TPI | Pitch |
|---|---|---|---|---|---|---|
| #0 | 0.06001.52 mm | 1.52 | – | 80 | 0.318 mm | |
| #1 | 0.07301.85 mm | 1.85 | 64 | 0.397 mm | 72 | 0.353 mm |
| #2 | 0.08602.18 mm | 2.18 | 56 | 0.454 mm | 64 | 0.397 mm |
| #3 | 0.09902.51 mm | 2.51 | 48 | 0.529 mm | 56 | 0.454 mm |
| #4 | 0.11202.84 mm | 2.84 | 40 | 0.635 mm | 48 | 0.529 mm |
| #5 | 0.12503.18 mm | 3.18 | 40 | 0.635 mm | 44 | 0.577 mm |
| #6 | 0.13803.51 mm | 3.51 | 32 | 0.794 mm | 40 | 0.635 mm |
| #8 | 0.16404.17 mm | 4.17 | 32 | 0.794 mm | 36 | 0.706 mm |
| #10 | 0.19004.83 mm | 4.83 | 24 | 1.058 mm | 32 | 0.794 mm |
| #12 | 0.21605.49 mm | 5.49 | 24 | 1.058 mm | 28 | 0.907 mm |
| 1/4 | 0.25006.35 mm | 6.35 | 20 | 1.270 mm | 28 | 0.907 mm |
| 5/16 | 0.31257.94 mm | 7.94 | 18 | 1.411 mm | 24 | 1.058 mm |
| 3/8 | 0.37509.53 mm | 9.53 | 16 | 1.588 mm | 24 | 1.058 mm |
| 7/16 | 0.437511.11 mm | 11.11 | 14 | 1.814 mm | 20 | 1.270 mm |
| 1/2 | 0.500012.70 mm | 12.70 | 13 | 1.954 mm | 20 | 1.270 mm |
| 9/16 | 0.562514.29 mm | 14.29 | 12 | 2.117 mm | 18 | 1.411 mm |
| 5/8 | 0.625015.88 mm | 15.88 | 11 | 2.309 mm | 18 | 1.411 mm |
| 11/16 | 0.687517.46 mm | 17.46 | – | – | ||
| 3/4 | 0.750019.05 mm | 19.05 | 10 | 2.540 mm | 16 | 1.588 mm |
| 13/16 | 0.812520.64 mm | 20.64 | – | – | ||
| 7/8 | 0.875022.23 mm | 22.23 | 9 | 2.822 mm | 14 | 1.814 mm |
| 15/16 | 0.937523.81 mm | 23.81 | – | – | ||
| 1 | 1.000025.40 mm | 25.40 | 8 | 3.175 mm | 12 | 2.117 mm |
| 1-1/8 | 1.125028.58 mm | 28.58 | 7 | 3.629 mm | 12 | 2.117 mm |
| 1-1/4 | 1.250031.75 mm | 31.75 | 7 | 3.629 mm | 12 | 2.117 mm |
| 1-3/8 | 1.375034.93 mm | 34.93 | 6 | 4.233 mm | 12 | 2.117 mm |
| 1-1/2 | 1.500038.10 mm | 38.10 | 6 | 4.233 mm | 12 | 2.117 mm |
| 1-3/4 | 1.750044.45 mm | 44.45 | 5 | 5.080 mm | – | |
| 2 | 2.000050.80 mm | 50.80 | 4.5 | 5.644 mm | – |
#0 has no coarse thread (#0-80 is UNF only). Major diameter is the basic size from ASME B1.1; a real screw measures a few thousandths under it.
| Size | Coarse pitch | TPI | Fine pitch | TPI |
|---|---|---|---|---|
| M1.6 | 0.35 mm | 72.57 | not covered | |
| M2 | 0.4 mm | 63.50 | not covered | |
| M2.5 | 0.45 mm | 56.44 | not covered | |
| M3 | 0.5 mm | 50.80 | not covered | |
| M3.5 | 0.6 mm | 42.33 | not covered | |
| M4 | 0.7 mm | 36.29 | not covered | |
| M5 | 0.8 mm | 31.75 | not covered | |
| M6 | 1 mm | 25.40 | 0.75 mm | 33.87 |
| M8 | 1.25 mm | 20.32 | 1 mm | 25.40 |
| M10 | 1.5 mm | 16.93 | 1.25, 1 mm | 20.32, 25.40 |
| M12 | 1.75 mm | 14.51 | 1.5, 1.25 mm | 16.93, 20.32 |
| M14 | 2 mm | 12.70 | 1.5 mm | 16.93 |
| M16 | 2 mm | 12.70 | 1.5 mm | 16.93 |
| M18 | 2.5 mm | 10.16 | 1.5 mm | 16.93 |
| M20 | 2.5 mm | 10.16 | 1.5 mm | 16.93 |
| M22 | 2.5 mm | 10.16 | 1.5 mm | 16.93 |
| M24 | 3 mm | 8.47 | 2 mm | 12.70 |
Coarse pitches are ISO 261. Fine pitches are the ones we cover with a checked tap drill. ISO 261 lists fine pitches for every size, including the small ones marked "not covered" (M3 x 0.35, for example), and more than we show for most others. TPI is 25.4 divided by the pitch, for comparison only: metric threads are never specified that way.
| Size | TPI | Pitch | Outside dia. | mm |
|---|---|---|---|---|
| 1/16 NPT | 27 | 0.941 mm | 0.3137.94 mm | 7.94 |
| 1/8 NPT | 27 | 0.941 mm | 0.40510.29 mm | 10.29 |
| 1/4 NPT | 18 | 1.411 mm | 0.54013.72 mm | 13.72 |
| 3/8 NPT | 18 | 1.411 mm | 0.67517.15 mm | 17.15 |
| 1/2 NPT | 14 | 1.814 mm | 0.84021.34 mm | 21.34 |
| 3/4 NPT | 14 | 1.814 mm | 1.05026.67 mm | 26.67 |
| 1 NPT | 11.5 | 2.209 mm | 1.31533.40 mm | 33.40 |
| 1-1/4 NPT | 11.5 | 2.209 mm | 1.66042.16 mm | 42.16 |
| 1-1/2 NPT | 11.5 | 2.209 mm | 1.90048.26 mm | 48.26 |
| 2 NPT | 11.5 | 2.209 mm | 2.37560.33 mm | 60.33 |
The NPT size is a pipe size, not a measurement: 1/4 NPT is about 0.54 in across. Outside diameter of the pipe from ASME B1.20.1.
Metric pitch to TPI, and the near misses
Several metric pitches land within a few percent of an inch TPI. The last column is how far the two threads drift apart over 10 turns: for the pairs under 1% it is less than 0.1 mm, so a pitch gauge leaf seats in either one and the gauge alone cannot tell them apart. Measure the diameter as well.
| Pitch | TPI | Used on | Close inch TPI | Off by | 10 turns |
|---|---|---|---|---|---|
| 0.35 mm | 72.57 | M1.6 | 72 #1-72 | 0.8% | 0.03 mm |
| 0.4 mm | 63.50 | M2 | 64 #1-64, #2-64 | 0.8% | 0.03 mm |
| 0.45 mm | 56.44 | M2.5 | 56 #2-56, #3-56 | 0.8% | 0.04 mm |
| 0.5 mm | 50.80 | M3 | none within 3% | ||
| 0.6 mm | 42.33 | M3.5 | none within 3% | ||
| 0.7 mm | 36.29 | M4 | 36 #8-36 | 0.8% | 0.06 mm |
| 0.75 mm | 33.87 | M6 | none within 3% | ||
| 0.8 mm | 31.75 | M5 | 32 #6-32, #8-32, #10-32 | 0.8% | 0.06 mm |
| 1 mm | 25.40 | M6, M8, M10 | none within 3% | ||
| 1.25 mm | 20.32 | M8, M10, M12 | 20 1/4-20, 7/16-20, 1/2-20 | 1.6% | 0.20 mm |
| 1.5 mm | 16.93 | M10, M12, M14, M16, M18, M20, M22 | none within 3% | ||
| 1.75 mm | 14.51 | M12 | none within 3% | ||
| 2 mm | 12.70 | M14, M16, M24 | 13 1/2-13 | 2.3% | 0.46 mm |
| 2.5 mm | 10.16 | M18, M20, M22 | 10 3/4-10 | 1.6% | 0.40 mm |
| 3 mm | 8.47 | M24 | none within 3% |
"Close" means within 3% of the metric pitch's TPI. A #10-32 screw is 4.83 mm across against 5 mm for M5 x 0.8, and with the pitches this close it can thread into the M5 hole while engaging less of the thread. Measure the diameter as well.
Questions
How many TPI is 1.5 mm?
A 1.5 mm pitch is 16.93 threads per inch (25.4 / 1.5). No Unified thread matches it: the closest is 16 TPI (3/8-16, 3/4-16), 5.8% off, so a 16 TPI gauge leaf rocks in a 1.5 mm thread and the two will not screw together.
What are the different metric thread sizes?
Metric threads are named by major diameter and pitch in millimeters: M8 x 1.25 is 8 mm across with 1.25 mm from one crest to the next. Each size has one coarse pitch, which is what a plain "M8" means, and one or more fine pitches. The common coarse sizes, from ISO 261, are M1.6 x 0.35, M2 x 0.4, M2.5 x 0.45, M3 x 0.5, M3.5 x 0.6, M4 x 0.7, M5 x 0.8, M6 x 1, M8 x 1.25, M10 x 1.5, M12 x 1.75, M14 x 2, M16 x 2, M18 x 2.5, M20 x 2.5, M22 x 2.5, M24 x 3.
Standards used: ASME B1.1 and ISO 261 / 965-1.