threadsizes

9/16-18 Tap Drill Size

Unified fine (UNF) · 18 threads per inch · ASME B1.1, class 2B

What size drill bit for a 9/16-18 tap?

33/64"fractional drill
0.5156inch
13.10mm
65%thread
No 33/64" drill? 12.9 mm (0.5079 in, 76%) or 13 mm (0.5118 in, 70%), both inside the 2B limits.
33/64" is the drill published charts list, but it is 0.0006 in over the 2B maximum minor diameter (0.5150 in).
Too small for steel 1/2" (87%): it makes the tap much harder to turn and easier to break.
Did the 33/64" drill work for you?

To scale section of the tapped hole

Section of a 9/16-18 tapped hole to scale: 33/64" drill, thread length 1.5 times the diameter, drilled 5 pitches deeper. Thread 1.5 × D = 0.844 in +5 P = 0.278 in ⌀0.5625 in major Pitch 0.0556 in (18 TPI) 33/64" drill ⌀0.5156 in
Drawn from the 9/16-18 basic profile. Hatched area is the part; the thread runs 1.5 × D and the drill goes 5 pitches deeper for a plug tap. Grab the PNG →

Drawing callout same hole, as a plan note

⌀.516 ↧1.12 / 9/16-18 UNF-2B ↧.84

Thread depth 1.5 × D, drilled 5 pitches deeper for a plug tap; change both to suit your part. Through hole for a screw instead? Use the clearance hole: ⌀.594 free fit (older ASME two-fit chart, clearance hole chart). How to read this →

Drill options % of thread

Drill options for 9/16-18
DrillInchmmThread2B
1/2" 0.5000 12.70 87% ✗
12.8 mm 0.5039 12.80 81% ✓
12.9 mm 0.5079 12.90 76% ✓
13 mm 0.5118 13.00 70% ✓
33/64"Use 0.5156 13.10 65% ✗

75% (orange tick) is the usual target. Hard or gummy metals like stainless are often tapped at 60 to 65% to spare the tap; aluminum, brass and plastic take 75% or a little more. The last column checks the hole against the 2B minor diameter limits (0.502 in to 0.515 in).

9/16-18 UNF ASME B1.1, class 2B

Major diameter0.5625 in / 14.29 mm
Threads per inch18 TPI (pitch 0.0556 in)
Pitch diameter 2B0.5264–0.5323 in
Minor diameter 2B0.5024–0.5150 in
Thread depth (basic, 5/8 H)0.0301 in
Forming tap drill (estimate)55% 35/64" 0.5417 in65% 17/32" 0.5379 in75% 17/32" 0.5342 in

Forming tap drills are estimates from the rule tap makers use (D − 0.0068 × % × pitch, in inches), shown at 55, 65 and 75% thread with the nearest drill; 65% is the usual starting point. Confirm with your tap maker's chart. Forming taps push the metal instead of cutting it, so never use this drill with a cutting tap.

Clearance hole older ASME two-fit chart

Close37/640.578 in
Free19/320.594 in

ASME B18.2.8-1999 Table 1 lists only preferred sizes and omits 9/16-18, so this size has no close / normal / loose fit in the current standard. The two drills above are from the older ASME two-fit convention, still reproduced in published charts; the Free value is what shops typically use when a modern “normal” fit is wanted. All sizes: clearance hole chart.

Wrench and key ASME B18.2.1, B18.2.2, B18.3

Hex nut7/8 in

Wrench across the flats of a standard hex bolt head and hex nut, and the Allen key for a socket head cap screw. All sizes in the bolt size chart.

Cross-checks published tables that agree

Tap drill 33/64"7 of 7
Minor diameter 2B2 of 2
Pitch diameter 2B2 of 3
Hex nut 7/8 in2 of 2

Tables that list the same value, out of those that list one; a reprint of another table counts once. How values are checked.

Hole depth rule of thumb

  • 0.563 inthread engagement to start from in steel (1 × D); the right figure depends on the materials, the thread class and the load
  • 0.844 inin cast iron or brass (1.5 × D), up to 1.125 in in aluminum
  • +0.278 inextra drill depth below the thread for a plug tap (5 pitches), +0.111 in with a bottoming tap

Full table and the ASME B1.1 formula: thread engagement chart.

Shop notes

The drill on most charts for 9/16-18 is 33/64 (0.5156 in), and it is a thin choice: about 65% thread, and just over the largest minor diameter class 2B allows. Charts list it because it is the nearest fraction, not because it is ideal.

If you have metric drills, 12.9 mm is the better hole: about 76% thread and inside the 2B limits. A 13 mm (70%) is also inside and easier on the tap in tough steel. Avoid going down to 1/2 in or 12.7 mm: at about 87% they are under the minimum minor diameter.

9/16-18 or M14 x 1.5?

A 9/16 bolt is 14.29 mm across, close enough to M14 x 1.5 (14 mm) to share a drawer, and the pitches are close too: 18 threads per inch is 1.41 mm against 1.5 mm. They still will not swap; the wrong one binds after a few turns. The coarse version, 9/16-12, takes a 31/64 drill.

Tapped 9/16-18?

Report a problem

Tell us what looks wrong on the 9/16-18 page and where your number comes from. Every report is checked against the standard.

What happened when you tapped 9/16-18? Reports appear on the page after a quick check.

Result

Ask about 9/16-18: drills, materials, depth, tap types. We answer here on the page; good questions move into the main text.