Standards
Every number on this site is calculated from the formulas of the thread, drill and fastener standards and compared with published charts. The standards used, grouped by what they define:
Thread form and dimensions
- ASME B1.1 — Unified inch screw threads (UNC, UNF, UNEF). Thread form, basic dimensions, class 2A/2B tolerances.
- ASME B1.13M — Metric screw threads, M profile (US adoption of the ISO form).
- ISO 261 — ISO general-purpose metric screw threads, standard sizes and pitches.
- ISO 965-1 — ISO general-purpose metric screw threads, tolerances (grades 4H, 5H, 6H, 6g…).
- ASME B1.20.1 — General-purpose pipe threads (NPT): pipe OD, TPI, hand-tight engagement L1.
- ISO 228-1 — Pipe threads where pressure-tight joints are not made on the threads: G (BSPP) parallel.
- ISO 7-1 and EN 10226-1 — Pipe threads where pressure-tight joints are made on the threads: R (BSPT) taper.
Hex bolts, nuts and socket head screws
- ASME B18.2.1 — Square, hex, heavy hex and askew head bolts (inch).
- ASME B18.2.2 — Nuts for general applications: machine screw nuts, hex, square, heavy hex (inch).
- ASME B18.3 — Socket cap, shoulder and set screws (inch).
- ISO 4017 — Hexagon head screws, thread fully to the head (metric).
- ISO 4032 — Hexagon regular nuts (style 1), metric.
- ISO 4762 — Hexagon socket head cap screws, metric.
Washers
- ASME B18.22.1 — Plain washers (inch), Type A narrow and wide series, sold as SAE and USS.
- ASME B18.21.1 — Lock washers (inch), helical spring regular series.
- ISO 7089 — Plain washers, normal series, product grade A (metric; replaced DIN 125-A).
- ISO 7093-1 — Plain washers, large series, product grade A (metric).
- DIN 9021 — Plain washers, large series, about three times the bolt diameter (metric; sold as fender washers).
- DIN 127 — Spring lock washers with square ends, form B (metric).
- ASTM F436 — Hardened steel washers (inch).
- Inch fender washers have no standard; the washer chart lists each maker's own values.
Clearance holes
- ASME B18.2.8 — Clearance holes for bolts, screws and studs (inch): close, normal, loose fit.
- ISO 273 — Fasteners — clearance holes for bolts and screws (metric): close, medium, coarse fit.
Drill diameters
- ASME B94.11M — Twist drills. Defines the diameters of number, letter and fractional drills in inch, and the metric drill series.
Formulas we use
The thread-engineering formulas that come straight out of these standards. With major diameter D and pitch P (P = 1 / threads per inch):
- Basic pitch diameter = D − 0.649519 × P (both inch and metric; the geometry of the 60° profile).
- Basic minor diameter of the nut = D − 1.082532 × P (ISO metric, D − P for the drill diameter rule of thumb).
- Basic thread height of the nut = 0.541266 × P.
- Percent of thread = (D − drill) ÷ (1.299038 × P) × 100. The convention in Machinery's Handbook and tap-maker charts. 75% is the usual design point; tap drills are the drill sizes that leave about that much thread for the tap.
- NPT pitch diameter at the small end: E0 = D − (0.05 × D + 1.1) × P, and effective thread length L2 = (0.8 × D + 6.8) × P (ASME B1.20.1).
- Same-strength engagement (ASME B1.1 Appendix B, B1.13M Appendix B): the engagement that makes the thread's shear strength equal to the screw's tensile strength when both are the same material. See the thread engagement chart for the full formula and worked examples.
- BSP / Whitworth: 55° thread angle with rounded crests and roots. The nut minor diameter equals major − 1.280654 × pitch.
Shop practice we label as such
Some advice on the thread pages is shop practice, not a standard, and the page says so: thread engagement of 1 × D in steel and 1.5 to 2 × D in softer metals (full table and the ASME B1.1 same-strength formula on the thread engagement chart), and drilling 5 pitches deeper than the thread for a plug tap.
Drawing callouts
Each thread page shows a one-line drawing callout for the tapped hole. The order and symbols follow the two conventions in common use:
- Inch (ASME): drill diameter and depth first, then the thread spec and thread depth. Example:
⌀.201 ↧.63 / 1/4-20 UNC-2B ↧.38. See ASME Y14.5 for the depth-to-full-diameter convention. - Metric (ISO): thread spec and thread depth first, then drill. Example:
M6x1-6H ↧9 / ⌀5 ↧14. See ISO 6410-1 for the general conventions of screw-thread representation and dimensioning.
Numbers come from the thread's own data: thread depth = 1.5 × D, drill depth = 1.5 × D + 5 pitches (the same rule the To scale drawing uses). The symbols are ⌀ (U+2300, diameter) and ↧ (U+21A7, depth). NPT pipe threads are not called out as a tapped-hole depth: the engagement is set by the taper, not drafted.
How values are checked
Each value is calculated from the standard first, then compared with tables published by fastener makers, distributors, tool makers and engineering references that reproduce the same standard. A tap drill, clearance hole, wrench or key size is listed only when at least two independent tables agree with it, allowing for the rounding they print; otherwise it shows as pending. A site that reprints another site's table, or one datasheet sold under two names, counts as one table.
Each thread page ends its data with a Cross-checks panel: for each value, how many tables agree out of how many list one, and what the others list when they disagree on the tap drill. The 45 thread pages are checked against 24 independent published tables.
Help us check a value
If you have a chart, catalog or handbook page that lists a value marked pending on the site, or you think a listed value is wrong, send a source.