threadsizes

Thread engagement chart (inch and metric)

How long does the thread have to be so the screw holds? The usual rule of thumb is 1 × D in steel, 1.5 × D in cast iron or brass and 2 × D in aluminum, where D is the screw's major diameter. This page gives those three lengths for every UNC, UNF, UNEF and metric thread the site publishes, plus the ASME B1.1 formula for the shortest length that gives the same strength as the screw itself.

Rule of thumb, by material of the internal thread

1 × DSteel
1.5 × DCast iron, brass, bronze
2 × DAluminum, zinc, magnesium
D is the screw's major diameter. These are start points, not a design rule: the right engagement depends on the materials, the thread class, the load and the screw's own strength. For a joint that has to carry the screw's full strength, use the ASME B1.1 formula below instead.

Thread engagement calculator

—inch

Rule of thumb, not a design calculation. For same-strength engagement (steel screw in a steel internal thread) use the ASME B1.1 formula under how it is calculated; a steel screw in a softer internal thread needs the length longer by its strength ratio (the J factor), which is what the material multiplier here approximates.

Inch (UNC / UNF / UNEF)

Engagement length by material, inch
Rule of thumb by material (in)
Thread D (in) TPI At (in2) Le (in) Threads Steel (1 × D) Cast iron / brass (1.5 × D) Aluminum (2 × D)
#2-56 0.086 56 0.0037 0.073 4.1 0.086 0.129 0.172
#4-40 0.112 40 0.0060 0.087 3.5 0.112 0.168 0.224
#6-32 0.138 32 0.0091 0.101 3.2 0.138 0.207 0.276
#8-32 0.164 32 0.0140 0.124 4.0 0.164 0.246 0.328
#10-24 0.190 24 0.0175 0.132 3.2 0.190 0.285 0.380
#10-32 0.190 32 0.0200 0.146 4.7 0.190 0.285 0.380
#12-24 0.216 24 0.0242 0.154 3.7 0.216 0.324 0.432
#12-28 0.216 28 0.0258 0.161 4.5 0.216 0.324 0.432
1/4-20 0.250 20 0.0318 0.174 3.5 0.250 0.375 0.500
1/4-28 0.250 28 0.0364 0.194 5.4 0.250 0.375 0.500
5/16-18 0.313 18 0.0524 0.223 4.0 0.313 0.469 0.625
5/16-24 0.313 24 0.0581 0.243 5.8 0.313 0.469 0.625
3/8-16 0.375 16 0.0775 0.270 4.3 0.375 0.563 0.750
3/8-24 0.375 24 0.0878 0.301 7.2 0.375 0.563 0.750
7/16-14 0.438 14 0.1063 0.314 4.4 0.438 0.656 0.875
7/16-20 0.438 20 0.1187 0.346 6.9 0.438 0.656 0.875
1/2-13 0.500 13 0.1419 0.363 4.7 0.500 0.750 1.000
1/2-20 0.500 20 0.1600 0.403 8.1 0.500 0.750 1.000
9/16-12 0.563 12 0.1819 0.409 4.9 0.563 0.844 1.125
9/16-18 0.563 18 0.2030 0.450 8.1 0.563 0.844 1.125
5/8-11 0.625 11 0.2260 0.453 5.0 0.625 0.938 1.250
5/8-18 0.625 18 0.2560 0.508 9.2 0.625 0.938 1.250
3/4-10 0.750 10 0.3345 0.550 5.5 0.750 1.125 1.500
3/4-16 0.750 16 0.3730 0.609 9.7 0.750 1.125 1.500
7/8-9 0.875 9 0.4617 pending – 0.875 1.313 1.750

Metric (ISO)

Engagement length by material, metric
Rule of thumb by material (mm)
Thread D (mm) Pitch (mm) As (mm2) Le (mm) Threads Steel (1 × D) Cast iron / brass (1.5 × D) Aluminum (2 × D)
M2 x 0.4 2 0.4 2.1 1.65 4.1 2 3 4
M3 x 0.5 3 0.5 5.0 2.58 5.2 3 4.5 6
M4 x 0.7 4 0.7 8.8 3.21 4.6 4 6 8
M5 x 0.8 5 0.8 14.2 4.01 5.0 5 7.5 10
M6 x 1 6 1 20.1 4.66 4.7 6 9 12
M8 x 1 8 1 39.2 6.53 6.5 8 12 16
M8 x 1.25 8 1.25 36.6 6.02 4.8 8 12 16
M10 x 1 10 1 64.5 8.4 8.4 10 15 20
M10 x 1.25 10 1.25 61.2 7.81 6.2 10 15 20
M10 x 1.5 10 1.5 58.0 7.44 5.0 10 15 20
M12 x 1.5 12 1.5 88.1 9.24 6.2 12 18 24
M12 x 1.75 12 1.75 84.3 8.88 5.1 12 18 24
M14 x 2 14 2 115.4 10.3 5.1 14 21 28
M16 x 2 16 2 156.7 12.01 6.0 16 24 32

D is the screw's major diameter. Tensile stress area is calculated from the thread's own geometry: At = 0.7854 × (D − 0.9743 / n)2 for inch threads (ASME B1.1), and As = (π / 4) × ((d2 + d3) / 2)2 for metric (ISO 898-1), with d2 = D − 0.649519 × P and d3 = D − 1.226869 × P. Le is the ASME B1.1 Appendix B equal-strength engagement for a steel screw in a steel internal thread (details in how it is calculated). The 1×D / 1.5×D / 2×D columns are the shop rule of thumb for different internal-thread materials, not a standard. Pipe threads (NPT) use hand-tight engagement L1 from ASME B1.20.1 instead and are on the NPT chart.

How it is calculated

Shop rule of thumb

The 1 × D in steel, 1.5 × D in cast iron or brass and 2 × D in aluminum come from the ratio of thread shear strength to the screw's own tensile strength. In steel the two are similar, so an engagement roughly equal to the diameter balances them; in softer metals the internal thread is weaker, so it has to be longer to catch up. These are the figures printed on the thread pages and in common machinery references (Machinery's Handbook, Bossard's Fastener Technology, Carroll Smith Nuts, Bolts, Fasteners and Plumbing Handbook). They are a start point, not a design calculation; strong joints have to be checked.

Same-strength engagement (ASME B1.1 and B1.13M Appendix B)

Assumption: the screw and the internal thread are the same material and the same strength. Under that hypothesis, the engagement length that makes the thread's shear strength equal to the screw's tensile strength is

Le = (2 × At) ÷ (π × Kn,max × [0.5 + 0.57735 × n × (Es,min − Kn,max)])

Where At is the tensile stress area of the screw (formula above), n is threads per inch (metric: n = 1 ÷ P), Kn,max is the internal thread's maximum minor diameter (class 2B for inch, 6H for metric) and Es,min is the external thread's minimum pitch diameter (class 2A for inch, 6g for metric). The 0.57735 is tan(30°), from the 60° thread angle. The formula appears in ASME B1.1 Appendix B for Unified inch threads and in ASME B1.13M Appendix B for ISO metric threads; both appendices note that it is an approximation and that geometry, friction and material matching all shift the real strength. The Le column in the chart above is calculated with this formula from the thread's own data: At, Kn,max and Es,min from the ASME B1.1 Table 3B (inch) and ASME B1.13M-1995 (metric) internal-thread tables. For a joint with dissimilar materials, apply the J factor correction below.

For 1/4-20 UNC 2A/2B the formula gives Le ≈ 0.174 in, about 0.70 × D (At = 0.0318 in2, Es,min = 0.2127 in, Kn,max = 0.2074 in, n = 20). The rule-of-thumb 1 × D = 0.250 in in the same row is a little longer and so a little conservative, which is on purpose: real screws are rarely in a perfectly machined 2B hole, and small tolerance differences shorten the thread. For M6x1 the formula gives Le ≈ 4.65 mm, where 1 × D is 6 mm.

Dissimilar materials: the J factor

When the screw is harder than the internal thread, which is the common case (a steel screw into aluminum, cast iron or brass), the engagement has to be longer than Le to make the thread as strong as the screw. The correction, called the J factor, is the ratio of the shear strengths of the two materials and is tabulated in ASME B1.1 Appendix B and in Machinery's Handbook as a function of specific alloys and heat treatments. The 1.5 × D and 2 × D rules in the chart above are shop practice that happens to correlate with the J factors of the most common cast-iron / brass and aluminum alloys when the screw is a Grade 5 or 8.8 steel; they are not derived from a fixed J value, so for a soft screw in a very soft housing or a hard screw in a tough bronze the ratio can be noticeably different. Work from the standard's table when the joint matters.

What this chart does not cover

The length columns are a shop rule, not an engineering calculation. They say nothing about pre-load, locking, embedment or the material's exact grade. For a joint that is loaded close to the screw's capacity, has thin walls, sees vibration or has a safety requirement, work from the standards above or your fastener maker's data. The standards and checks page lists what this site calculates and what is shop practice.

Questions

How much thread engagement is needed?

Start with 1 x D in steel, 1.5 x D in cast iron or brass, and 2 x D in aluminum, where D is the screw's major diameter. For a 1/4-20 screw that is 1/4 in in steel, 3/8 in in cast iron and 1/2 in in aluminum. These are start points: the length that gives the full strength of the screw itself comes from the ASME B1.1 formula and depends on both materials.

What is the thread engagement rule of thumb?

The common rule is 1 x D in steel, 1.5 x D in cast iron or brass, and 2 x D in aluminum. It appears in Machinery's Handbook, Bossard's Fastener Technology and FED-STD-H28/2B, and matches the strength-ratio correction (J factor) in ASME B1.1 Appendix B for those material pairs.

Does more thread engagement make the joint stronger?

Up to a point. Beyond the length that makes the thread shear strength equal to the screw tensile strength, extra engagement adds very little: the screw breaks before the thread does, so making the thread stronger does not change the joint. Published tests show the gain flattens out around 1.5 x D in steel into steel. The main reason to go longer is a softer internal thread or a safety margin against uncertainty.

How do I calculate the exact engagement length?

Use Le = (2 x At) / (pi x Kn,max x [0.5 + 0.57735 x n x (Es,min - Kn,max)]) from ASME B1.1 Appendix B. For a screw harder than the internal thread, multiply the result by the J factor from the same appendix. The formula uses the external thread class 2A minimum pitch diameter and the internal thread class 2B maximum minor diameter, which are tabulated in the standard.