threadsizes

9/16-12 Tap Drill Size

Unified coarse (UNC) · 12 threads per inch · ASME B1.1, class 2B

What size drill bit for a 9/16-12 tap?

Just a 9/16 tap? Coarse 9/16-12 takes a 31/64" drill (this page); fine 9/16-18 takes a 33/64" drill. The full size is marked on the tap shank; if it is worn, count threads per inch.

31/64"fractional drill
0.4844inch
12.30mm
72%thread
No 31/64" drill? 12.2 mm (0.4803 in, 76%) or 12.3 mm (0.4843 in, 72%), both inside the 2B limits.
Too small for steel 15/32" (87%): it makes the tap much harder to turn and easier to break.
Did the 31/64" drill work for you?

To scale section of the tapped hole

Section of a 9/16-12 tapped hole to scale: 31/64" drill, thread length 1.5 times the diameter, drilled 5 pitches deeper. Thread 1.5 × D = 0.844 in +5 P = 0.417 in ⌀0.5625 in major Pitch 0.0833 in (12 TPI) 31/64" drill ⌀0.4844 in
Drawn from the 9/16-12 basic profile. Hatched area is the part; the thread runs 1.5 × D and the drill goes 5 pitches deeper for a plug tap. Grab the PNG →

Drawing callout same hole, as a plan note

⌀.484 ↧1.26 / 9/16-12 UNC-2B ↧.84

Thread depth 1.5 × D, drilled 5 pitches deeper for a plug tap; change both to suit your part. Through hole for a screw instead? Use the clearance hole: ⌀.594 free fit (older ASME two-fit chart, clearance hole chart). How to read this →

Drill options % of thread

Drill options for 9/16-12
DrillInchmmThread2B
15/32" 0.4688 11.91 87% ✗
12 mm 0.4724 12.00 83% ✓
12.1 mm 0.4764 12.10 80% ✓
12.2 mm 0.4803 12.20 76% ✓
12.3 mm 0.4843 12.30 72% ✓
31/64"Use 0.4844 12.30 72% ✓
12.4 mm 0.4882 12.40 69% ✓
12.5 mm 0.4921 12.50 65% ✗
12.6 mm 0.4961 12.60 61% ✗
1/2" 0.5000 12.70 58% ✗

By material Aluminum, brass, mild steel: 31/64" (72%) · Stainless, tool steel: 12.4 mm (69%)

75% (orange tick) is the usual target. Hard or gummy metals like stainless are often tapped at 60 to 65% to spare the tap; aluminum, brass and plastic take 75% or a little more. The last column checks the hole against the 2B minor diameter limits (0.472 in to 0.490 in).

9/16-12 UNC ASME B1.1, class 2B

Major diameter0.5625 in / 14.29 mm
Threads per inch12 TPI (pitch 0.0833 in)
Pitch diameter 2B0.5084–0.5152 in
Minor diameter 2B0.4723–0.4903 in
Thread depth (basic, 5/8 H)0.0451 in
Forming tap drill (estimate)55% 17/32" 0.5313 in65% 17/32" 0.5257 in75% 33/64" 0.5200 in

Forming tap drills are estimates from the rule tap makers use (D − 0.0068 × % × pitch, in inches), shown at 55, 65 and 75% thread with the nearest drill; 65% is the usual starting point. Confirm with your tap maker's chart. Forming taps push the metal instead of cutting it, so never use this drill with a cutting tap.

Clearance hole older ASME two-fit chart

Close37/640.578 in
Free19/320.594 in

ASME B18.2.8-1999 Table 1 lists only preferred sizes and omits 9/16-12, so this size has no close / normal / loose fit in the current standard. The two drills above are from the older ASME two-fit convention, still reproduced in published charts; the Free value is what shops typically use when a modern “normal” fit is wanted. All sizes: clearance hole chart.

Wrench and key ASME B18.2.1, B18.2.2, B18.3

Hex nut7/8 in

Wrench across the flats of a standard hex bolt head and hex nut, and the Allen key for a socket head cap screw. All sizes in the bolt size chart.

Cross-checks published tables that agree

Tap drill 31/64"7 of 7
Minor diameter 2B2 of 2
Pitch diameter 2B2 of 3
Hex nut 7/8 in2 of 2

Tables that list the same value, out of those that list one; a reprint of another table counts once. How values are checked.

Hole depth rule of thumb

  • 0.563 inthread engagement to start from in steel (1 × D); the right figure depends on the materials, the thread class and the load
  • 0.844 inin cast iron or brass (1.5 × D), up to 1.125 in in aluminum
  • +0.417 inextra drill depth below the thread for a plug tap (5 pitches), +0.167 in with a bottoming tap

Full table and the ASME B1.1 formula: thread engagement chart.

Shop notes

31/64 (0.4844 in) is the standard 9/16-12 tap drill: about 72% thread, inside the 2B limits. A 12.2 mm drill (76%) or a 12.3 mm (72%) does the same job if your set is metric.

Going smaller fast becomes too much: 12 mm is already about 83%, which is a lot of torque on a tap this size. Going bigger, 1/2 in and 12.7 mm drop to about 58% and fall outside the limits, so a 1/2 in drill is not the shortcut it looks like.

9/16-12 or M14 x 2?

The closest metric thread is M14 x 2: 14 mm against 14.29 mm, and 2 mm pitch against 2.12 mm. Close enough to start, different enough to strip. The fine version, 9/16-18, is a different hole altogether.

Tapped 9/16-12?

Report a problem

Tell us what looks wrong on the 9/16-12 page and where your number comes from. Every report is checked against the standard.

What happened when you tapped 9/16-12? Reports appear on the page after a quick check.

Result

Ask about 9/16-12: drills, materials, depth, tap types. We answer here on the page; good questions move into the main text.