threadsizes

M14 Tap Drill Size (M14 x 2.0)

ISO metric coarse · 2 mm pitch · ISO 261 / 965-1, class 6H

What size drill bit for an M14 tap?

12 mmmetric drill
0.4724inch
12.00mm
77%thread
No 12 mm drill? 15/32" (0.4688 in, 81%, harder to tap, above all by hand and in steel), inside the 6H limits.
Too small for steel 11.9 mm (81%): it makes the tap much harder to turn and easier to break.
Did the 12 mm drill work for you?

To scale section of the tapped hole

Section of a M14 x 2 tapped hole to scale: 12 mm drill, thread length 1.5 times the diameter, drilled 5 pitches deeper. Thread 1.5 × D = 21 mm +5 P = 10 mm ⌀14 mm major Pitch 2 mm 12 mm drill ⌀12.00 mm
Drawn from the M14 x 2 basic profile. Hatched area is the part; the thread runs 1.5 × D and the drill goes 5 pitches deeper for a plug tap. Grab the PNG →

Drawing callout same hole, as a plan note

M14x2-6H ↧21 / ⌀12 ↧31

Thread depth 1.5 × D, drilled 5 pitches deeper for a plug tap; change both to suit your part. Through hole for a screw instead? Use the clearance hole: ⌀15.5 normal fit (ISO 273, clearance hole chart). How to read this →

Drill options % of thread

Drill options for M14 x 2
DrillInchmmThread6H
11.8 mm 0.4646 11.80 85% ✗
11.9 mm 0.4685 11.90 81% ✓
15/32" 0.4688 11.91 81% ✓
12 mmUse 0.4724 12.00 77% ✓
12.1 mm 0.4764 12.10 73% ✓
12.2 mm 0.4803 12.20 69% ✓
12.3 mm 0.4843 12.30 65% ✗
31/64" 0.4844 12.30 65% ✗
12.4 mm 0.4882 12.40 62% ✗

By material Aluminum, brass, mild steel: 12 mm (77%) · Stainless, tool steel: 12.2 mm (69%)

75% (orange tick) is the usual target. Hard or gummy metals like stainless are often tapped at 60 to 65% to spare the tap; aluminum, brass and plastic take 75% or a little more. The last column checks the hole against the 6H minor diameter limits (11.83 mm to 12.21 mm).

M14 x 2 ISO 261, 965-1, class 6H

Major diameter14 mm / 0.5512 in
Pitch2 mm
Pitch diameter 6H12.701–12.913 mm
Minor diameter 6H11.835–12.210 mm
Thread depth (basic, 5/8 H)1.083 mm
Forming tap drill (estimate)55% 13.5 mm 13.25 mm65% 13 mm 13.12 mm75% 13 mm 12.98 mm

Forming tap drills are estimates from the rule tap makers use (D − 0.0068 × % × pitch, in inches), shown at 55, 65 and 75% thread with the nearest drill; 65% is the usual starting point. Confirm with your tap maker's chart. Forming taps push the metal instead of cutting it, so never use this drill with a cutting tap.

Clearance hole ISO 273

Close15 mm15 mm
Normal15.5 mm15.5 mm
Loose16.5 mm16.5 mm

For a screw that passes through the part. Normal fit is the default; close fit locates the part more accurately but allows less error in hole position. All sizes: clearance hole chart.

Wrench and key ISO 4017, 4032, 4762

Hex head21 mm
Hex nut21 mm

Wrench across the flats of a standard hex bolt head and hex nut, and the Allen key for a socket head cap screw. Older DIN 933 heads, still sold, take 22 mm. All sizes in the bolt size chart.

Cross-checks published tables that agree

Tap drill 12 mm2 of 3
Minor diameter 6H2 of 2
Pitch diameter 6H2 of 2
Clearance holes5 of 5
Hex head 21 mm3 of 3

Tables that list the same value, out of those that list one; a reprint of another table counts once. The other table lists 12.2 mm for the tap drill. How values are checked.

Hole depth rule of thumb

  • 14 mmthread engagement to start from in steel (1 × D); the right figure depends on the materials, the thread class and the load
  • 21 mmin cast iron or brass (1.5 × D), up to 28 mm in aluminum
  • +10 mmextra drill depth below the thread for a plug tap (5 pitches), +4 mm with a bottoming tap

Full table and the ASME B1.1 formula: thread engagement chart.

Shop notes

M14 x 2 is the coarse M14 and the drill is 12 mm, the ISO rule of diameter minus pitch: 14 − 2 = 12. That gives about 77% thread, inside the 6H limits. A 12.1 mm (73%) is a little easier on the tap in stainless.

The inch drill that works is 15/32 (0.4688 in, about 81%, inside the limits). 31/64 looks closer to 12 mm on paper but cuts only about 65% and is over the maximum minor diameter.

M14 sits next to 9/16-12 (14.29 mm, 2.12 mm pitch), and the two get mixed up. M14 x 2 is also common in one spot you might not expect: many spark plugs use a 14 mm thread, but that is the fine M14 x 1.25, not this one.

Tapped M14 x 2?

Report a problem

Tell us what looks wrong on the M14 x 2 page and where your number comes from. Every report is checked against the standard.

What happened when you tapped M14 x 2? Reports appear on the page after a quick check.

Result

Ask about M14 x 2: drills, materials, depth, tap types. We answer here on the page; good questions move into the main text.