BSP thread chart (BSPP & BSPT)
British Standard Pipe is the pipe thread used across Europe, the Commonwealth and much of Asia. One thread form, 55 degree Whitworth with rounded crests and roots, in two variants: G (BSPP) is parallel and sealed by an O-ring or gasket; R (BSPT) is tapered 1 in 16 on the diameter and seals on the threads with PTFE tape. Both share the same TPI and major diameter at a given size, so one table does for both. Sizes are nominal pipe bores, not measurements.
threadsizes.com/bsp-thread-chart · printed Nov 20, 2026 · check critical dimensions against the standard
BSP in one line
G / BSPP parallel, ISO 228-1
| Size | TPI | Pitch | Major dia. | mm | Minor dia. | mm | G drill |
|---|---|---|---|---|---|---|---|
| G 1/16 | 28 | 0.907 mm | 0.30417.72 mm | 7.72 | 0.25836.56 mm | 6.56 | 6.80 mmH |
| G 1/8 | 28 | 0.907 mm | 0.38309.73 mm | 9.73 | 0.33728.57 mm | 8.57 | 8.80 mmS |
| G 1/4 | 19 | 1.337 mm | 0.518013.16 mm | 13.16 | 0.450611.45 mm | 11.45 | 11.80 mm15/32" |
| G 3/8 | 19 | 1.337 mm | 0.656016.66 mm | 16.66 | 0.588614.95 mm | 14.95 | 15.25 mm19/32" |
| G 1/2 | 14 | 1.814 mm | 0.825020.96 mm | 20.96 | 0.733518.63 mm | 18.63 | 19.00 mm3/4" |
| G 3/4 | 14 | 1.814 mm | 1.041026.44 mm | 26.44 | 0.949524.12 mm | 24.12 | 24.50 mm31/32" |
| G 1 | 11 | 2.309 mm | 1.309033.25 mm | 33.25 | 1.192630.29 mm | 30.29 | 30.75 mm1-13/64" |
| G 1-1/4 | 11 | 2.309 mm | 1.650041.91 mm | 41.91 | 1.533538.95 mm | 38.95 | 39.50 mm1-9/16" |
| G 1-1/2 | 11 | 2.309 mm | 1.882047.80 mm | 47.80 | 1.765644.85 mm | 44.85 | 45.25 mm1-25/32" |
| G 2 | 11 | 2.309 mm | 2.347059.61 mm | 59.61 | 2.230656.66 mm | 56.66 | 57.00 mm2-1/4" |
G threads do not seal on their own: a G fitting is sealed with an O-ring, a bonded washer or a flat gasket on a face around the thread. Pitch is 25.4 ÷ TPI (so a 14 TPI pitch is 1.814 mm). Minor diameter is the standard value for the nut; it equals major − 1.280654 × pitch, the 55 degree Whitworth form.
R / BSPT taper, ISO 7-1
| Size | TPI | Pitch | Major dia. at gauge | mm | Gauge length | Rp drill | Rc drill |
|---|---|---|---|---|---|---|---|
| R 1/16 | 28 | 0.907 mm | 0.30417.72 mm | 7.72 | 4.0 mm | 6.50 mmF | 6.20 mmD |
| R 1/8 | 28 | 0.907 mm | 0.38309.73 mm | 9.73 | 4.0 mm | 8.50 mmQ | 8.20 mmP |
| R 1/4 | 19 | 1.337 mm | 0.518013.16 mm | 13.16 | 6.0 mm | 11.40 mm29/64" | 10.90 mm27/64" |
| R 3/8 | 19 | 1.337 mm | 0.656016.66 mm | 16.66 | 6.4 mm | 14.90 mm19/32" | 14.40 mm9/16" |
| R 1/2 | 14 | 1.814 mm | 0.825020.96 mm | 20.96 | 8.2 mm | 18.50 mm47/64" | 18.00 mm45/64" |
| R 3/4 | 14 | 1.814 mm | 1.041026.44 mm | 26.44 | 9.5 mm | 24.00 mm15/16" | 23.00 mm29/32" |
| R 1 | 11 | 2.309 mm | 1.309033.25 mm | 33.25 | 10.4 mm | 30.20 mm1-3/16" | 29.00 mm1-9/64" |
| R 1-1/4 | 11 | 2.309 mm | 1.650041.91 mm | 41.91 | 12.7 mm | 39.00 mm1-17/32" | 38.00 mm1-1/2" |
| R 1-1/2 | 11 | 2.309 mm | 1.882047.80 mm | 47.80 | 12.7 mm | 45.00 mm1-49/64" | 44.00 mm1-47/64" |
| R 2 | 11 | 2.309 mm | 2.347059.61 mm | 59.61 | 15.9 mm | 56.40 mm2-7/32" | 55.00 mm2-11/64" |
R threads are cut on a taper of 1 in 16 on the diameter: the diameter in the table is the gauge-plane diameter, which is the same number as the G major diameter at the same nominal size. The gauge length is how far from the small end that reference diameter sits.
Rc = tapered internal thread (use a 1:16 pipe reamer before the tap). Rp = parallel internal thread. G = parallel ISO 228-1. Drill sizes are tap-maker recommendations, not ISO; cross-checked against Swagelok’s Thread and End Connection Identification Guide (MS-13-77).
Heads up: the Rc drill sizes above assume the hole is reamed with a 1:16 pipe reamer before tapping. If you are tapping without a reamer, use a slightly larger drill (tap-maker charts list this as the “drill only” column).
BSP vs NPT
BSP and NPT share one thing: the taper rate, 1 in 16 on the diameter. Everything else differs. Where the TPI matches, as it does at 1/2 and 3/4 inch, the thread angle still does not (55° vs 60°), so the flanks of a BSP thread sit at a different angle to the axis than those of an NPT thread. The two will not seal together, and forcing a BSP male into an NPT female damages the female thread. Use a dedicated adapter between the two systems.
| Size | BSP TPI | BSP pitch | NPT TPI | NPT pitch | Interchange? |
|---|---|---|---|---|---|
| 1/16 | 28 | 0.907 mm | 27 | 0.941 mm | No different TPI and flank angle |
| 1/8 | 28 | 0.907 mm | 27 | 0.941 mm | No different TPI and flank angle |
| 1/4 | 19 | 1.337 mm | 18 | 1.411 mm | No different TPI and flank angle |
| 3/8 | 19 | 1.337 mm | 18 | 1.411 mm | No different TPI and flank angle |
| 1/2 | 14 | 1.814 mm | 14 | 1.814 mm | No same TPI, 55° vs 60° flanks |
| 3/4 | 14 | 1.814 mm | 14 | 1.814 mm | No same TPI, 55° vs 60° flanks |
| 1 | 11 | 2.309 mm | 11-1/2 | 2.209 mm | No different TPI and flank angle |
| 1-1/4 | 11 | 2.309 mm | 11-1/2 | 2.209 mm | No different TPI and flank angle |
| 1-1/2 | 11 | 2.309 mm | 11-1/2 | 2.209 mm | No different TPI and flank angle |
| 2 | 11 | 2.309 mm | 11-1/2 | 2.209 mm | No different TPI and flank angle |
NPT values from the NPT tap drill chart (ASME B1.20.1). Pitches shown in mm for direct comparison with BSP, which is specified in mm. Need the background? What is NPT? covers the 1 in 16 taper, L1 hand-tight and NPTF.
How to tell BSP from NPT
- Thread gaugeSet a pitch gauge: a 55° leaf seats on BSP, a 60° leaf on NPT. Many combination gauges have both.
- Crests and rootsBSP crests and roots are rounded (Whitworth form). NPT crests and roots are flat (Sellers form, truncated).
- Flank angleMeasure or compare against a gauge: BSP flanks sit at 27.5° off the axis, NPT at 30°.
- MarkingsFittings are often marked with the standard: G for BSPP (ISO 228-1), R or Rp or Rc for BSPT (ISO 7-1), or NPT / ANSI B1.20.1. No marking defaults to the regional norm, which is NPT in North America and BSP almost everywhere else.
If the markings are gone and a pitch gauge is not to hand, measure the diameter at the thread crest and check it against the chart above for BSP and the NPT chart for NPT. At the same nominal size the two diameters differ by a few hundredths of a millimetre (1/2 BSP is 20.96 mm, 1/2 NPT is 21.34 mm), which is enough to tell them apart with a caliper.
Questions
Is 1/2 BSP the same as 1/2 NPT?
No. BSP uses a 55 degree thread angle (Whitworth) and NPT uses 60 degrees (Sellers). At 1/2 inch nominal they both have 14 threads per inch, but a 1/2 BSP major diameter is 20.96 mm and a 1/2 NPT male thread is 21.34 mm at its large end: the pitches match on the gauge but the flanks do not, so the two will not seal together. Use an adapter.
Does the BSP number refer to the pipe or the thread?
The pipe. BSP sizes, like NPT sizes, are nominal pipe bores, so a 1/2 BSP thread is not 1/2 inch across: it is 20.96 mm (0.825 in) on the outside.
What is the difference between BSPP and BSPT?
They are the same thread form (ISO 228-1 for G/BSPP and ISO 7-1 for R/BSPT, both 55 degree Whitworth) at the same TPI and major diameter. G is parallel: it holds the parts together but needs an O-ring or washer to seal. R is tapered 1 in 16 on the diameter: it wedges tighter as it goes in and seals on the threads themselves with PTFE tape or a pipe sealant.
Values marked pending* are left blank until enough published sources agree. Have a chart that lists one of them? Send a source. More on how numbers get onto this site: standards and checks.