Pilot hole size chart for wood and sheet-metal screws
A pilot hole is the small hole you drill before a screw so the thread cuts cleanly into the material. For wood screws the right drill depends on the species, a touch smaller in softwood than in hardwood because the fibres displace more easily; the values are a woodworking convention. For sheet-metal / self-tapping screws — Types A, AB and B — the drill is set by ASME B18.6.4 against a specific test-plate thickness. A “#8 wood screw” is not a #8-32 machine screw — same gauge diameter, different thread (see screw sizes explained).
threadsizes.com/pilot-hole-chart · printed Nov 20, 2026 · check critical dimensions against the standard
Pilot hole in one line
Wood screws, #4 to #14
| Size | Diameter | mm | Pilot — Hardwood | Pilot — Softwood |
|---|---|---|---|---|
| #4 | 0.112 in2.85 mm | 2.85 | 5/64"0.0781 · 1.99 mm | 1/16"0.0625 · 1.59 mm |
| #6 | 0.138 in3.51 mm | 3.51 | 7/64"0.1094 · 2.78 mm | 3/32"0.0938 · 2.38 mm |
| #8 | 0.164 in4.17 mm | 4.17 | 1/8"0.1250 · 3.18 mm | 7/64"0.1094 · 2.78 mm |
| #10 | 0.190 in4.83 mm | 4.83 | 9/64"0.1406 · 3.57 mm | 1/8"0.1250 · 3.18 mm |
| #12 | 0.216 in5.49 mm | 5.49 | 5/32"0.1563 · 3.97 mm | 9/64"0.1406 · 3.57 mm |
| #14 | 0.242 in6.15 mm | 6.15 | 11/64"0.1719 · 4.37 mm | 5/32"0.1563 · 3.97 mm |
Drill names are the ordinary fractional twist drill; the decimal inch and mm equivalents are from the drill table (ANSI/ASME B94.11M for fractional drills). The hardwood column uses a slightly larger drill than the softwood column because dense fibres resist displacement more. These values are a woodworking convention, not a standard.
Sheet-metal & self-tapping screws (ASME B18.6.4)
Sheet-metal screws share the same gauge numbers as wood screws but have a different thread, and the pilot hole doesn’t just depend on the screw: it also depends on the sheet thickness and material. ASME B18.6.4 gives one recommended drill per screw size, measured against a specific test-plate thickness. In practice that drill works down to about half the test thickness (shift one size smaller) and up to about twice it (shift one size larger). The three thread types below all form their mating thread as they go in: Type AB (gimlet point, spaced thread), Type B (blunt point, same thread as AB), Type A (coarser thread, from #6 upwards). Self-drilling screws (“Tek” screws) have a drill point and need no pilot in thin sheet; see the FAQ below.
Thread dimensions
| Size | Type | TPI | Major MAX | Major MIN | Minor MAX | Minor MIN |
|---|---|---|---|---|---|---|
| #2 | AB / B | 32 | 0.0880 in2.24 mm | 0.0820 in2.08 mm | 0.0640 in1.63 mm | 0.0600 in1.52 mm |
| #3 | AB / B | 28 | 0.1010 in2.57 mm | 0.0950 in2.41 mm | 0.0750 in1.91 mm | 0.0710 in1.80 mm |
| #4 | AB / B | 24 | 0.1140 in2.90 mm | 0.1080 in2.74 mm | 0.0860 in2.18 mm | 0.0820 in2.08 mm |
| #5 | AB / B | 20 | 0.1300 in3.30 mm | 0.1230 in3.12 mm | 0.0940 in2.39 mm | 0.0900 in2.29 mm |
| #6 | AB / B | 20 | 0.1390 in3.53 mm | 0.1320 in3.35 mm | 0.1040 in2.64 mm | 0.0990 in2.52 mm |
| #6 | A | 18 | 0.1410 in3.58 mm | 0.1360 in3.45 mm | 0.1020 in2.59 mm | 0.0960 in2.44 mm |
| #7 | AB / B | 19 | 0.1540 in3.91 mm | 0.1470 in3.73 mm | 0.1150 in2.92 mm | 0.1090 in2.77 mm |
| #7 | A | 16 | 0.1580 in4.01 mm | 0.1520 in3.86 mm | 0.1140 in2.90 mm | 0.1080 in2.74 mm |
| #8 | AB / B | 18 | 0.1660 in4.22 mm | 0.1590 in4.04 mm | 0.1220 in3.10 mm | 0.1160 in2.95 mm |
| #8 | A | 15 | 0.1680 in4.27 mm | 0.1620 in4.12 mm | 0.1230 in3.12 mm | 0.1160 in2.95 mm |
| #10 | AB / B | 16 | 0.1890 in4.80 mm | 0.1820 in4.62 mm | 0.1410 in3.58 mm | 0.1350 in3.43 mm |
| #10 | A | 12 | 0.1940 in4.93 mm | 0.1880 in4.78 mm | 0.1330 in3.38 mm | 0.1260 in3.20 mm |
| #12 | AB / B | 14 | 0.2150 in5.46 mm | 0.2080 in5.28 mm | 0.1640 in4.17 mm | 0.1570 in3.99 mm |
| #12 | A | 11 | 0.2210 in5.61 mm | 0.2150 in5.46 mm | 0.1620 in4.12 mm | 0.1550 in3.94 mm |
| 1/4 | AB / B | 14 | 0.2460 in6.25 mm | 0.2370 in6.02 mm | 0.1920 in4.88 mm | 0.1850 in4.70 mm |
| 5/16 | AB / B | 12 | 0.3150 in8.00 mm | 0.3060 in7.77 mm | 0.2440 in6.20 mm | 0.2360 in5.99 mm |
| 3/8 | AB / B | 12 | 0.3800 in9.65 mm | 0.3710 in9.42 mm | 0.3090 in7.85 mm | 0.2990 in7.60 mm |
| #14 | A | 10 | 0.2540 in6.45 mm | 0.2480 in6.30 mm | 0.1850 in4.70 mm | 0.1780 in4.52 mm |
| #20 | A | 9 | 0.3330 in8.46 mm | 0.3270 in8.31 mm | 0.2340 in5.94 mm | 0.2260 in5.74 mm |
| #24 | A | 9 | 0.3900 in9.91 mm | 0.3830 in9.73 mm | 0.2910 in7.39 mm | 0.2820 in7.16 mm |
Major diameter is the outer thread; minor diameter is the root between threads. Types AB and B share thread dimensions (the difference is the point: AB has a gimlet point, B has a blunt point). Type A has a coarser thread and starts at #6. Decimal inches are reproduced from the standard; mm are inch × 25.4 rounded to 0.001.
Recommended pilot hole
| Size × TPI | Type | Pilot drill | Hole diameter | ASME test plate |
|---|---|---|---|---|
| #2–32 | AB / B | #480.0760 · 1.93 mm | 0.0760 in1.93 mm | 18 ga0.0460–0.0500 in |
| #3–28 | AB / B | #460.0810 · 2.06 mm | 0.0810 in2.06 mm | 18 ga0.0460–0.0500 in |
| #4–24 | AB / B | #440.0860 · 2.18 mm | 0.0860 in2.18 mm | 18 ga0.0460–0.0500 in |
| #5–20 | AB / B | #360.1065 · 2.71 mm | 0.1065 in2.71 mm | 18 ga0.0460–0.0500 in |
| #6–20 | AB / B | #320.1160 · 2.95 mm | 0.1160 in2.95 mm | 14 ga0.0730–0.0770 in |
| #6–18 | A | #320.1160 · 2.95 mm | 0.1160 in2.95 mm | — |
| #7–19 | AB / B | #300.1285 · 3.26 mm | 0.1285 in3.26 mm | 14 ga0.0730–0.0770 in |
| #7–16 | A | #300.1285 · 3.26 mm | 0.1285 in3.26 mm | — |
| #8–18 | AB / B | #290.1360 · 3.45 mm | 0.1360 in3.45 mm | 14 ga0.1230–0.1270 in |
| #8–15 | A | #290.1360 · 3.45 mm | 0.1360 in3.45 mm | — |
| #10–16 | AB / B | #210.1590 · 4.04 mm | 0.1590 in4.04 mm | 1/8 ga0.1230–0.1270 in |
| #10–12 | A | #210.1590 · 4.04 mm | 0.1590 in4.04 mm | — |
| #12–14 | AB / B | 3/16"0.1875 · 4.76 mm | 0.1875 in4.76 mm | 1/8 ga0.1230–0.1270 in |
| #12–11 | A | 3/16"0.1875 · 4.76 mm | 0.1875 in4.76 mm | — |
| 1/4–14 | AB / B | 5.5 mm0.2165 · 5.50 mm | 0.2165 in5.50 mm | 3/16 ga0.1845–0.1905 in |
| 5/16–12 | AB / B | I0.2720 · 6.91 mm | 0.2720 in6.91 mm | 3/16 ga0.1845–0.1905 in |
| 3/8–12 | AB / B | 21/64"0.3281 · 8.34 mm | 0.3281 in8.33 mm | 3/16 ga0.1845–0.1905 in |
| #14–10 | A | 5.5 mm0.2165 · 5.50 mm | 0.2165 in5.50 mm | — |
| #20–9 | A | L0.2900 · 7.37 mm | 0.2900 in7.37 mm | — |
| #24–9 | A | 11/32"0.3438 · 8.73 mm | 0.3438 in8.73 mm | — |
Values are from ASME B18.6.4 “Suggested Test Plate Thicknesses & Hole Sizes”. Each is the drill the standard uses to qualify the screw’s torsional strength on a plate of the stated gage. In thinner material drop one drill size; in thicker material step one up. Type A has no test-plate column in the standard’s Type A chart: the recommendation is the closest drill to the mean of major and minor diameters. These hole sizes are drilled or clean-punched; pierced or extruded holes allow a smaller drill (see the standard’s hole-preparation note).
Shank clearance hole
The pilot hole is for the threaded part of the screw. When a screw passes through a top piece and threads into a second piece behind it, the top piece gets a larger clearance hole for the plain shank, so the shank slips through and the threads pull the two pieces tight together. The diagram and the walk-through are in the screw sizes guide. Shank-hole drill values aren’t on this chart yet. Send a source if you have a shank-hole chart to suggest.
Lag screws (coming)
Lag screws are heavier, hex-head wood screws, 1/4 in to 1/2 in. The AWC NDS specifies the lead (pilot) hole as a percentage of the shank diameter — 65–85% depending on wood specific gravity — so no single drill fits every species. A lag-screw section is in the works. For now, the diameter and head sizes of hex-head bolts and lag-style fasteners are on the bolt size chart.
Questions
What size pilot hole for a #8 wood screw?
1/8" in hardwood, 7/64" in softwood. A #8 wood screw is 0.164 in (4.17 mm) across its outer thread; the pilot is a touch smaller than that so the screw cuts a thread as it goes in.
Do I need a pilot hole in softwood?
Yes, especially close to an edge or in dry wood. The softwood drill is smaller than the hardwood one because the fibres displace more easily: for a #8 wood screw, 7/64" in softwood vs 1/8" in hardwood. Without a pilot, pine and spruce split along the grain.
What size pilot hole for a #10 sheet-metal screw?
#21 (0.1590 in / 4.04 mm) for Type AB or Type B, per ASME B18.6.4. The standard sets this against a test plate 1/8 gage (0.1230–0.1270 in) thick. In thinner sheet you can go a size smaller, in thicker sheet a size larger, but staying near this value keeps the screw within its standard-tested torque range.
What size pilot hole for a 1/4 self-tapping screw?
5.5 mm (0.2165 in) for Type AB or Type B 1/4-14, per ASME B18.6.4. The test plate is 3/16 gage (0.1845–0.1905 in) thick.
Self-tapping vs self-drilling screw: what’s the difference?
A self-tapping screw (Type A, AB or B here) needs a pilot hole: it forms its own mating thread as it goes in. A self-drilling screw — often sold as a Tek screw — has a small drill point at the tip, so in thin sheet it drills and taps in one go without a pilot hole. In thicker material (above the point’s drilling capacity) a self-drilling screw still needs a pre-drilled hole.
Can you use sheet-metal screws in wood?
They hold, but they’re not the right tool. Sheet-metal screws have fully-threaded shanks and sharp thread crests designed to bite into thin metal; in wood they tend to split the fibres and have no plain shank to pull two pieces together. For wood use a wood screw, or a construction screw with a plain upper shank. See screw sizes explained.
Is a #8 wood screw the same as a #8-32 machine screw?
No. A wood screw cuts its own thread into wood with a coarse profile and no machine-screw pitch. A #8-32 is a machine screw with 32 threads per inch, meant for a nut or a tapped hole. They are the same gauge diameter but will not interchange: the threads do not match. See screw sizes explained.
What size pilot hole for a 5/16 lag screw?
Lag screws are heavier, hex-head wood screws from 1/4 in to 1/2 in; the AWC NDS gives the lead hole as a percentage of the shank diameter by wood specific gravity, so one drill does not fit every species. A lag-screw section is in the works.
Have a shank-hole or lag-screw chart to suggest? Send a source. More on how numbers get onto this site: standards and checks.