Heat-set insert hole size chart
Brass heat-set inserts give a steel thread in a 3D-printed or injection-moulded plastic part. There is no governing standard, so each manufacturer publishes their own geometry; the right hole depends on the exact insert. This chart lists what each maker publishes for its own range, M2 to M6, in millimetres.
threadsizes.com/heat-set-insert-chart · printed Nov 20, 2026 · check critical dimensions against the standard
| Maker | Model | Length mm | Hole Ø mm | Insert OD mm | Min wall mm |
|---|---|---|---|---|---|
| CNC Kitchen | Standard | 3 | 3.2 * | 3.6 | 1.3 |
| ruthex | Standard | 4 | 3.2 * | 3.6 | 1.3 |
| McMaster | 96975A114 | 4 | 3.1 * | – | – |
| Maker | Model | Length mm | Hole Ø mm | Insert OD mm | Min wall mm |
|---|---|---|---|---|---|
| CNC Kitchen | Standard | 4 | 4 * | 4.6 | 1.6 |
| McMaster | 96975A115 | 5.7 | 3.9 * | – | – |
| Maker | Model | Length mm | Hole Ø mm | Insert OD mm | Min wall mm |
|---|---|---|---|---|---|
| CNC Kitchen | Standard | 5.7 | 4 * | 4.6 | 1.6 |
| ruthex | Standard | 5.7 | 4 | 4.6 | 1.6 |
| McMaster | 96975A116 | 5.7 | 3.9 * | – | – |
| CNC Kitchen | Short | 3 | 4 * | 4.6 | 1.6 |
| CNC Kitchen | Voron | 4 | 4.4 * | 5 | 1.3 |
| Maker | Model | Length mm | Hole Ø mm | Insert OD mm | Min wall mm |
|---|---|---|---|---|---|
| CNC Kitchen | Standard | 8.1 | 5.6 * | 6.3 | 2.1 |
| ruthex | Standard | 8.1 | 5.6 * | 6.3 | 2.1 |
| McMaster | 96975A118 | 8.2 | 5.5 * | – | – |
| CNC Kitchen | Short | 4 | 5.6 * | 6.3 | 2.1 |
| Maker | Model | Length mm | Hole Ø mm | Insert OD mm | Min wall mm |
|---|---|---|---|---|---|
| CNC Kitchen | Standard | 9.5 | 6.4 * | 7.1 | 2.6 |
| ruthex | Standard | 9.5 | 6.4 * | 7.1 | 2.6 |
| McMaster | 96975A119 | 9.5 | 6.3 * | – | – |
| CNC Kitchen | Short | 5.8 | 6.4 * | 7.1 | 2.6 |
| Maker | Model | Length mm | Hole Ø mm | Insert OD mm | Min wall mm |
|---|---|---|---|---|---|
| CNC Kitchen | Standard | 12.7 | 8 * | 8.7 | 3.3 |
| McMaster | 96975A121 | 12.7 | 7.9 * | – | – |
Hole Ø is the diameter the maker recommends you model (or drill, for a moulded part). Insert OD is the maximum diameter of the insert's knurled section; Min wall is the smallest amount of plastic the maker wants around the insert. McMaster-Carr's 96975A series publishes only hole and length. CNC Kitchen's and ruthex's M3, M4 and M5 Standard rows list the same dimensions because they are published by two separate manufacturers; two makers publishing the same number is not the same as two independent measurements agreeing, which is why only the row backed by an outside test is marked verified.
* Maker-only: the only published source for the value is the maker itself. The row is correct per that maker's own data sheet but has no independent measurement or test to back it up. Have a published test or measurement? Send a source.
Designing the hole
A heat-set insert goes into a straight hole in the plastic. The hole should be a touch bigger than the insert's smooth tip so the insert can be pre-seated, and smaller than the knurled section so molten plastic has somewhere to flow. The depth should be a little longer than the insert, so there is somewhere for displaced plastic to go beneath it.
A printed hole often comes out smaller than the model, especially on holes aligned with the build plate. The amount depends on the printer, nozzle, filament and orientation, so measure yours: print a strip of holes stepping up from the maker's recommended size and check with a drill bit as a go gauge. A moulded or machined hole can go straight to the maker's number.
Install the insert with a soldering iron fitted with an insert tip (the shape centres the insert and keeps it square). Set the iron a little above the filament's print temperature, press the insert in slowly, let it cool before loading the thread. If the insert sinks below flush or spins when a screw is tightened, the hole was too big; if it tears a cone of plastic up around it, too small. See the stripped-hole guide for the metal cousins (helical coil, solid bushings) that go into a tapped hole in metal — these are a different mechanism.
Inch sizes (coming)
Several makers list 4-40, 6-32, 8-32, 10-32 and 1/4-20 heat-set inserts, but the published data overlaps less tidily than for metric sizes and we have not yet captured two independent sources for any inch row. The data will be added here once each row is backed by a maker data sheet and an independent measurement, same rule as the metric table.
Questions
What size hole for an M3 heat-set insert?
CNC Kitchen and ruthex both publish 4 mm; McMaster-Carr's 96975A116 brass insert takes a 3.9 mm hole. ruthex's 4 mm is confirmed by an independent pull-out test (181 kg of pull-out at that hole size). The right value depends on the exact insert, and printed holes often come out undersize, so print a test coupon before committing.
Do I need to tap the hole for a heat-set insert?
No. A heat-set insert goes into a straight hole; a soldering iron melts the surrounding plastic and the knurling on the insert bonds as the plastic cools. There is no cut thread in the plastic — the thread is in the brass sleeve.
Heat-set insert vs tapping plastic directly?
A cut thread in plastic strips easily; even in a 3D-printed boss with plenty of material around it, pull-out force drops into tens of kilos. In a published pull-out test on PLA, an M3 screw straight into a 2.7 mm hole held 142 kg, while the same screw in a ruthex heat-set insert in its recommended 4 mm hole held 181 kg, and the direct-screw hole degrades much faster if you unscrew and reinsert.
Can I use heat-set inserts in wood or metal?
No. Heat-set inserts rely on melting thermoplastic around the knurling, so they only work in thermoplastic parts (PLA, PETG, ABS, ASA, PA, PC, etc.). For stripped threads in metal, a helical coil or solid thread insert; for wood, a glued plug or a threaded insert made for wood (see fix a stripped screw hole).
No governing standard. Each manufacturer designs their own insert and publishes their own recommended hole, so the chart rows are per-maker and per-model, not a universal number. Full method: standards and checks.