threadsizes

Rivet nut (rivnut) drill size chart

A rivet nut is a threaded sleeve installed from one side of a sheet or tube: drill a hole, pull the back of the body into a bulge against the sheet, and you get a full female thread in material too thin to tap. There is no governing standard, so each manufacturer designs its own body and publishes its own recommended hole. This chart lists what each maker publishes, M3 to M10 and 6-32 to 3/8-16, in millimetres and inches.

For a standard round-body M6: PennEngineering publishes 9.1 mm*; Avdel (Stanley) publishes 9.55 mm*; Böllhoff publishes 8.5 mm*; Gesipa publishes 9.1 mm*. Hex-body and slotted PLUSNUT versions take different holes — see the M6 table below for your model. Always check the datasheet for the exact part number before drilling a hole you cannot undo.
M3 rivet nuts (per manufacturer)
Maker Model Body Hole Ø mm Hole Ø in Grip mm Flange Ø × h mm
PennEngineering Sherex-by-PEM standard round body Round, smooth 5.1 +0.1 * 0.201 – –
PennEngineering Atlas AETR (thin head round body) Round, smooth 5 +0.1 * 0.197 0.5–2 7.4
Avdel (Stanley) Nutsert 9658 (steel, low profile, open end) Round, smooth 4.75 +0.1 * 0.187 0.51–1.5 8.4 × 0.38
Avdel (Stanley) Nutsert 9468 (stainless, low profile, open end) Round, smooth 4.75 +0.1 * 0.187 0.51–1.5 8.4 × 0.64
Avdel (Stanley) Eurosert 09408 (steel splined, low profile) Round, splined 5 +0.1 * 0.197 0.25–2 7.4 × 0.75
Avdel (Stanley) Nutsert FW78 (aluminium, large flange) Round, smooth, large flange 5.1 +0.1 * 0.201 0.25–2 10.5 × 0.75
M4 rivet nuts (per manufacturer)
Maker Model Body Hole Ø mm Hole Ø in Grip mm Flange Ø × h mm
PennEngineering Sherex-by-PEM standard round body Round, smooth 6.1 +0.1 * 0.240 – –
PennEngineering Atlas AETR (thin head round body) Round, smooth 6 +0.1 * 0.236 0.5–2.5 –
Avdel (Stanley) Nutsert 9658 (steel, low profile, open end) Round, smooth 6.35 +0.1 * 0.250 0.51–2 10.3 × 0.51
Avdel (Stanley) Nutsert FS58 (steel, large flange, closed end) Round, smooth, large flange 6.1 +0.1 * 0.240 0.5–2.5 10.5 × 0.8
Avdel (Stanley) Hexsert 9498 (steel, large flange, hex body) Hex body 6 +0.1 * 0.236 0.5–2 9.2 × 1
Böllhoff RIVNUT SM (flat head round body, steel) Round, smooth 5.62 +0.12 * 0.221 0.25–4 9 × 0.81
Böllhoff PLUSNUT (slotted body) Slotted (bulb-form), large flange 6.13 +0.12 * 0.241 0.5–6.85 11.1 × 0.96
Gesipa Standard aluminium small head (1433685) Round, smooth 6.1 * 0.240 – 9
M5 rivet nuts (per manufacturer)
Maker Model Body Hole Ø mm Hole Ø in Grip mm Flange Ø × h mm
PennEngineering Sherex-by-PEM standard round body Round, smooth 7.1 +0.1 * 0.280 – –
PennEngineering Atlas AETR (thin head round body) Round, smooth 7 +0.1 * 0.276 0.5–3 –
Avdel (Stanley) Nutsert 9658 (steel, low profile, open end) Round, smooth 7.15 +0.1 * 0.282 0.51–3 12.7 × 0.51
Avdel (Stanley) Nutsert FS58 (steel, large flange, closed end) Round, smooth, large flange 7.1 +0.1 * 0.280 0.5–2.5 13.3 × 1
Avdel (Stanley) Hexsert 9498 (steel, large flange, hex body) Hex body 7 +0.1 * 0.276 0.5–3 11.2 × 1
Böllhoff RIVNUT SM (flat head round body, steel) Round, smooth 7.2 +0.1 * 0.284 0.25–6.5 11.2 × 1.22
Böllhoff RIVNUT SMH (flat head hex body, steel) Hex body 6.36 +0.14 * 0.250 0.5–3.55 9.5 × 1.09
Böllhoff PLUSNUT (slotted body) Slotted (bulb-form), large flange 7.48 +0.14 * 0.295 0.5–8.1 12.7 × 0.96
Gesipa PolyGrip stainless A2 (1464888) Round, smooth 7.1 * 0.280 – –
M6 rivet nuts (per manufacturer)
Maker Model Body Hole Ø mm Hole Ø in Grip mm Flange Ø × h mm
PennEngineering Sherex-by-PEM standard round body Round, smooth 9.1 +0.1 * 0.358 – –
PennEngineering Atlas AETR (thin head round body) Round, smooth 9 +0.1 * 0.354 0.5–3 –
Avdel (Stanley) Nutsert 9658 (steel, low profile, open end) Round, smooth 9.55 +0.1 * 0.376 0.76–3.25 15.5 × 0.76
Avdel (Stanley) Nutsert FS58 (steel, large flange, closed end) Round, smooth, large flange 9.1 +0.1 * 0.358 0.5–3 15 × 1.5
Avdel (Stanley) Hexsert 9498 (steel, large flange, hex body) Hex body 9 +0.1 * 0.354 0.5–3 13.4 × 1.5
Böllhoff RIVNUT SM (flat head round body, steel) Round, smooth 8.5 +0.1 * 0.335 0.75–6.5 13.4 × 1.47
Böllhoff RIVNUT SMH (flat head hex body, steel) Hex body 7.54 +0.12 * 0.297 0.5–3.65 11.1 × 1.09
Böllhoff PLUSNUT (slotted body) Slotted (bulb-form), large flange 8.8 +0.13 * 0.347 0.5–12.7 15.9 × 1.5
Gesipa PolyGrip aluminium dome head (1433792) Round, smooth 9.1 * 0.358 – 12
M8 rivet nuts (per manufacturer)
Maker Model Body Hole Ø mm Hole Ø in Grip mm Flange Ø × h mm
PennEngineering Sherex-by-PEM standard round body Round, smooth 11.1 +0.1 * 0.437 – –
PennEngineering Atlas AETR (thin head round body) Round, smooth 11 +0.1 * 0.433 0.5–3 11
Avdel (Stanley) Nutsert 9658 (steel, low profile, open end) Round, smooth 10.6 +0.1 * 0.417 0.91–3.7 17.2 × 0.76
Avdel (Stanley) Nutsert FS58 (steel, large flange, closed end) Round, smooth, large flange 11.1 +0.1 * 0.437 1–4 18.6 × 1.5
Avdel (Stanley) Hexsert 9498 (steel, large flange, hex body) Hex body 11 +0.1 * 0.433 0.5–3 16.2 × 1.5
Böllhoff RIVNUT SM (flat head round body, steel) Round, smooth 10.5 +0.2 * 0.413 1–9 16.7 × 1.57
Böllhoff RIVNUT SMH (flat head hex body, steel) Hex body 10.11 +0.12 * 0.398 0.5–4.55 15.1 × 1.57
Böllhoff PLUSNUT (slotted body) Slotted (bulb-form), large flange 11.11 +0.39 * 0.437 0.5–12.7 19 × 1.57
Gesipa PolyGrip aluminium dome head (1455561) Round, smooth 11.1 * 0.437 – 14
M10 rivet nuts (per manufacturer)
Maker Model Body Hole Ø mm Hole Ø in Grip mm Flange Ø × h mm
PennEngineering Sherex-by-PEM standard round body Round, smooth 13.1 +0.1 * 0.516 – –
Avdel (Stanley) Nutsert 9658 (steel, low profile, open end) Round, smooth 14.2 +0.1 * 0.559 1–3.6 23.3 × 0.76
Avdel (Stanley) Hexsert 9498 (steel, large flange, hex body) Hex body 13 +0.1 * 0.512 1–3.5 18.5 × 2
Böllhoff RIVNUT SM (flat head round body, steel) Round, smooth 12.5 +0.2 * 0.492 1–10.5 19.5 × 2.23
Böllhoff RIVNUT SMH (flat head hex body, steel) Hex body 11.91 +0.23 * 0.469 0.75–5.2 17.5 × 1.57
Böllhoff PLUSNUT (slotted body) Slotted (bulb-form), large flange 13.07 +0.19 * 0.515 0.5–12.7 22.2 × 2.24
6-32 rivet nuts (per manufacturer)
Maker Model Body Hole Ø mm Hole Ø in Grip mm Flange Ø × h mm
Sherex CFW/CAW (diamond knurled 360° swaging, steel) Round, knurled 5.94 +0.13 * 0.234 – –
Sherex CAL (large flange knurled thin wall, stainless) Round, knurled, large flange 6.76 +0.15 * 0.266 0.51–2.03 10.67
Böllhoff RIVNUT S (flat head round body open, steel) Round, smooth 4.83 +0.08 * 0.190 0.25–3.05 8.26 × 0.81
Böllhoff PLUSNUT (slotted body) Slotted (bulb-form), large flange 5.31 +0.13 * 0.209 0.51–6.86 11.13 × 0.81
8-32 rivet nuts (per manufacturer)
Maker Model Body Hole Ø mm Hole Ø in Grip mm Flange Ø × h mm
Sherex CFW/CAW (diamond knurled 360° swaging, steel) Round, knurled 6.76 +0.13 * 0.266 – –
Sherex CAL (large flange knurled thin wall, stainless) Round, knurled, large flange 6.76 +0.15 * 0.266 0.05–2.03 10.67
Böllhoff RIVNUT S (flat head round body open, steel) Round, smooth 5.64 +0.1 * 0.222 0.25–4.06 9.07 × 0.81
Böllhoff PLUSNUT (slotted body) Slotted (bulb-form), large flange 6.15 +0.13 * 0.242 0.51–6.86 11.13 × 0.97
10-24 rivet nuts (per manufacturer)
Maker Model Body Hole Ø mm Hole Ø in Grip mm Flange Ø × h mm
Sherex CFW/CAW (diamond knurled 360° swaging, steel) Round, knurled 7.54 +0.13 * 0.297 – –
Sherex CAL (large flange knurled thin wall, stainless) Round, knurled, large flange 7.54 +0.15 * 0.297 0.51–3.3 12.07
10-32 rivet nuts (per manufacturer)
Maker Model Body Hole Ø mm Hole Ø in Grip mm Flange Ø × h mm
Sherex CFW/CAW (diamond knurled 360° swaging, steel) Round, knurled 7.54 +0.13 * 0.297 – –
Sherex CAL (large flange knurled thin wall, stainless) Round, knurled, large flange 7.54 +0.15 * 0.297 0.51–3.3 12.07
Böllhoff RIVNUT S (flat head round body open, steel) Round, smooth 6.38 +0.13 * 0.251 0.25–5.84 10.31 × 0.97
Böllhoff RIVNUT SH (flat head hex body, steel, standard hex) Hex body 5.69 +0.13 * 0.224 0.25–3.43 8.74 × 1.09
Böllhoff PLUSNUT (slotted body) Slotted (bulb-form), large flange 6.93 +0.13 * 0.273 0.51–8.13 12.7 × 0.97
1/4-20 rivet nuts (per manufacturer)
Maker Model Body Hole Ø mm Hole Ø in Grip mm Flange Ø × h mm
Sherex CFW/CAW (diamond knurled 360° swaging, steel) Round, knurled 9.93 +0.13 * 0.391 – –
Sherex CAL (large flange knurled thin wall, stainless) Round, knurled, large flange 9.93 +0.15 * 0.391 0.69–4.19 14.73
Böllhoff RIVNUT S (flat head round body open, steel) Round, smooth 8.46 +0.13 * 0.333 0.51–6.6 12.07 × 1.47
Böllhoff RIVNUT SH (flat head hex body, steel, standard hex) Hex body 7.54 +0.13 * 0.297 0.51–3.68 11.1 × 1.09
Böllhoff PLUSNUT (slotted body) Slotted (bulb-form), large flange 8.81 +0.13 * 0.347 0.51–12.7 15.88 × 1.47
5/16-18 rivet nuts (per manufacturer)
Maker Model Body Hole Ø mm Hole Ø in Grip mm Flange Ø × h mm
Sherex CFW/CAW (diamond knurled 360° swaging, steel) Round, knurled 13.49 +0.13 * 0.531 – –
Böllhoff RIVNUT S (flat head round body open, steel) Round, smooth 10.52 +0.23 * 0.414 0.76–8.89 16.89 × 1.57
Böllhoff RIVNUT SH (flat head hex body, steel, standard hex) Hex body 9.37 +0.13 * 0.369 0.76–4.45 14.27 × 1.22
Böllhoff PLUSNUT (slotted body) Slotted (bulb-form), large flange 11.13 +0.13 * 0.438 0.51–12.7 19.05 × 1.57
3/8-16 rivet nuts (per manufacturer)
Maker Model Body Hole Ø mm Hole Ø in Grip mm Flange Ø × h mm
Sherex CFW/CAW (diamond knurled 360° swaging, steel) Round, knurled 15.09 +0.13 * 0.594 – –
Böllhoff RIVNUT S (flat head round body open, steel) Round, smooth 12.47 +0.23 * 0.491 0.76–9.4 19.84 × 2.24
Böllhoff RIVNUT SH (flat head hex body, steel, standard hex) Hex body 11.13 +0.13 * 0.438 0.76–5.21 16.66 × 1.47
Böllhoff PLUSNUT (slotted body) Slotted (bulb-form), large flange 13.08 +0.18 * 0.515 0.51–12.7 22.23 × 2.24

Hole Ø is the diameter the maker recommends you drill (or hex-punch, for hex-body rows: the number is the width across flats). A +n suffix after a value is the one-sided tolerance band the maker publishes above the nominal size; blank where the maker does not publish one. Grip is the sheet-thickness range the body is designed to clamp over; the sheet must fall inside it. Flange is the outer diameter and head height, where published.

* Maker-only: the only published source for the value is the maker itself. The row is correct per that maker's own data sheet but has no independent measurement or test to back it up. At the time of writing no row on this chart has an independent second source. Have a published test or measurement? Send a source.

Picking the hole

Three things set the hole: body type, sheet thickness and surface finish. The body type decides the hole shape — a round smooth body and a knurled body both take a round drill, a hex body wants a hex-punched hole (a round one lets the body spin as you tighten a screw), and a slotted PLUSNUT body wants its own round diameter that leaves room for the legs to fold out. Match the hole to the row, not to the thread.

The sheet must fall inside the maker's grip range. If the sheet is thinner than the minimum grip, there is nothing for the rear bulge to clamp against and the body spins; if it is thicker than the maximum, the body cannot collapse. PLUSNUT and other long-grip bodies exist specifically for sheets outside the standard range; the Grip column in the tables above shows the exact min and max per row.

Deburr the hole on both sides, especially the back. A burr or raised edge sits between the flange and the sheet and keeps the flange from pulling flat; the body then setts crooked and the thread sits off-square. A countersink on the front face is normal where the maker publishes a countersunk head.

Related tools: heat-set inserts (the plastic-part cousin: a knurled brass sleeve pushed in with a soldering iron), clearance holes for the screw going into the rivet nut, and the tap drill chart or metric chart for cases where the sheet is thick enough to tap directly.

Questions

What size hole for an M6 rivet nut?

There is no universal number: each manufacturer designs its own body. For a standard round-body M6, PennEngineering Sherex-by-PEM standard round body is 9.1 mm (+0.1); Avdel (Stanley) Nutsert 9658 is 9.55 mm (+0.1); Böllhoff RIVNUT SM is 8.5 mm (+0.1); Gesipa PolyGrip aluminium dome head is 9.1 mm. Hex-body versions (Avdel Hexsert, Böllhoff RIVNUT SMH) need a hex-punched hole; the slotted PLUSNUT body wants its own round diameter — see the hex-body and PLUSNUT rows in the M6 table for the exact numbers. Always check the datasheet for the exact part number and drill a test hole in scrap first.

How do rivet nuts work?

A rivet nut is a threaded sleeve with a thin-wall rear section. You drill a hole in the sheet or tube, push the rivet nut in from the accessible side, and pull it with a mandrel tool that screws into its internal thread. The thin rear section collapses into a bulge against the back of the sheet, locking the nut in place, like a pop rivet with a thread inside it. The result is a full-strength internal thread in material too thin to tap. Standard-body grip ranges cover common sheet-metal thicknesses; the slotted PLUSNUT body stretches the range to much thicker sections. The Grip column in the table above shows the min and max per row.

Rivnut vs Plusnut vs Nutsert: what's the difference?

These are maker brand names and body styles. Rivnut is Böllhoff's original 1930s product and is now used as a generic word for the family. Nutsert is Avdel/Stanley Engineered Fastening's brand for the same kind of part. Plusnut is Böllhoff's slotted-body variant: the shank is pre-cut into six legs that fold out under the back of the sheet instead of forming a smooth bulb, which spreads the clamping load and tolerates a much wider sheet-thickness range. On the chart above, the Nutsert 9658 and FS58 rows are smooth round bodies, Hexsert and RIVNUT SMH/SH are the hex-body versions, and PLUSNUT is the slotted-body version.

Rivet nut or tap the sheet?

Thin sheet holds only a thread or two, so it strips easily. See the thread engagement chart: a steel-into-steel joint wants about one thread diameter of engaged length. A rivet nut carries that length in its own sleeve, so a thin panel can still take a full-strength thread. A tapped hole is only better where the sheet is already thick enough on its own.

No governing standard. Rivet-nut hole sizes are set by each manufacturer for each body style, so always check the datasheet for the exact part number and drill a test hole in a scrap of the actual sheet first. Sources: PennEngineering rivet nut hole-size chart, PEM Atlas AETR catalog, Avdel blind threaded inserts catalog (05.2011, 52 pp), Böllhoff RIVNUT USA catalog, Sherex CFW/CAW steel (inch), Sherex CAL stainless (inch), Gesipa PolyGrip and Standard product pages (M6, M8, M5, M4). Full method: standards and checks.