Metric bolt sizes explained
Updated October 17, 2026
An M8 bolt is 8 mm across the threads (about 0.315 in), with a standard coarse pitch of 1.25 mm, and a standard hex head takes a 13 mm wrench. An M6 bolt is 6 mm across, with a 1 mm pitch and a 10 mm wrench. That pattern holds for every metric size: the number after the M is the outside diameter of the thread in millimeters, and nothing else.
How a metric bolt size is written
A full size reads M8 x 1.25 x 30. The M says ISO metric thread. 8 is the thread diameter in millimeters, measured across the crests. 1.25 is the pitch, the distance from one thread to the next in millimeters. 30 is the length in millimeters, measured from under the head to the tip on a hex bolt (a countersunk screw is measured overall; see screw sizes explained).
So "what does M8 mean" has a short answer: an 8 mm metric thread. It says nothing about the head, the length, the strength or the material. Those come from the rest of the description: the head standard (such as ISO 4017), the length and the property class (such as 8.8).

When the pitch is missing: coarse and fine
Every metric size has one coarse pitch, the standard one. When the pitch is left out (M8 x 30, or just "M8"), coarse is meant. Some sizes also come in one or more fine pitches, written out every time: M8 x 1, M10 x 1.25, M12 x 1.5. Fine pitches are used where a shallower thread or a smaller step per turn helps, such as thin walls and adjusters. They need their own tap and nut, so a fine-pitch bolt will not thread into a coarse hole of the same diameter. The trade-offs between coarse and fine work the same way as for inch threads: see UNC vs UNF.
Inch readers can check the pitch by converting: an M6 x 1 has 25.4 threads per inch, which is why a 1/4-20 (20 TPI) will not go in it. If a bolt might be inch rather than metric, SAE vs metric walks through telling them apart.
How big M3 to M24 really are
Each size in one place, with its pitch, wrench, nut, Allen key, tap drill and clearance hole, is in the bolt size chart. For every metric thread and its drill options, see the metric tap drill chart.
Head and wrench sizes
The wrench size is the distance across the flats of the head. For hex bolts to ISO 4017 (threaded up to the head) and ISO 4014 (with a plain shank), the heads are the same; ISO 4032 hex nuts take the same wrench as the bolt.
| Bolt | Wrench (ISO) | Older DIN |
|---|---|---|
| M3 | 5.5 mm | same |
| M4 | 7 mm | same |
| M5 | 8 mm | same |
| M6 | 10 mm | same |
| M8 | 13 mm | same |
| M10 | 16 mm | 17 mm |
| M12 | 18 mm | 19 mm |
| M14 | 21 mm | 22 mm |
| M16 | 24 mm | same |
| M18 | 27 mm | same |
| M20 | 30 mm | same |
| M22 | 34 mm | 32 mm |
| M24 | 36 mm | same |
Four sizes changed when the ISO standard replaced DIN 933 and 931: M10, M12, M14 and M22. Bolts made to the older DIN standard are still around, which is why an M10 bolt may need a 16 mm or a 17 mm wrench. Flange bolts and some small-series heads are smaller again, so if the wrench in the table does not fit, measure the flats.
Drilling for a metric bolt
A bolt that threads into the part needs the tap drill, then a tap; a bolt that passes through needs the clearance hole. The bolt size chart gives both. To check a drill you already own against a thread, use the thread calculator, and for the tapping itself, how to tap a hole.